One of the major obstacles to the reuse of recycled plastic materials is the emanation of after-process odors from recycled polymers and composites. Typically, recycled polymers are blended with an off-odor adsorbent additive in the recycling chain to eliminate these smells. This article describes an innovative ultrasonically assisted method of grafting poly(ethylene imine) (PEI) to silica nanoparticles (SiO2) initiated by benzoyl peroxide (BP) which acts as an odor remover. To prepare the PEI/Si, the branched PEI was grafted onto the silica surface without a coupling agent. This made the grafting process straightforward, easy and low in cost. Fourier Transform Infrared (FTIR) analysis confirmed the successful grafting of PEI to silica. The thermogravimetric analysis (TGA) indicated the formation of two different fractions: a polymeric fraction covalently attached to the nanoparticle surface and a non-grafted PEI fraction that was removed during extraction. Up to 30% of the grafted-PEI fractions were produced at the lowest BP concentration with the highest PEI molecular weight at silica-to-PEI weight ratios of (1:1) to (3:1). The sensory assessment showed a substantial reduction in overall odor intensity for 30% of the recycled plastic-containing materials and a ~75% reduction in volatile organic compounds (VOCs) for 100% of the recycled plastics. These results strongly suggest that this innovative PEI/Si nanocomposite can be successfully commercialized for odor removal. To the authors’ best knowledge, this is the first reported work describing a one-pot reaction for grafting PEI to different nanoparticle surfaces.

This manuscript describes a novel in situ interfacial dynamic inverse emulsion polymerization process under sonication of aniline in the presence of carbon nanotubes (CNT) and graphene nanoparticles in ethanol. This polymerization method is simple and very rapid (up to 10 min) compared to other techniques reported in the literature. During polymerization, the nanoparticles are coated with polyaniline (PANI), forming a core-shell structure, as confirmed by high-resolution scanning electron microscopy (HRSEM) and Fourier-Transform Infrared (FTIR) measurements. The membrane pore sizes range between 100–200 nm, with an average value of ~119 ± 28.3 nm. The film resistivity decreased when treated with alcohol, and this behavior was used for selection of the most efficient alcohol as a solvent for this polymerization technique. The membrane permeability of the PANI grafted CNT was lower than the CNT reference, thus demonstrating better membranal properties. As measured by water permeability, these are ultrafiltration membranes. An antimicrobial activity test showed that whereas the reference nanoparticle Bucky paper developed a large bacterial colony, the PANI grafted CNT sample had no bacterial activity. The thicker, 2.56 mm membranes exhibited high salt removal properties at a low pressure drop. Such active membranes comprise a novel approach for future water treatment applications.

Meeting global water quality standards is a real challenge to ensure that food crops and livestock are fit for consumption, as well as for human health in general. A major hurdle affecting the detection of pollutants in water reservoirs is the lapse of time between the sampling moment and the availability of the laboratory-based results. Here, we report the preparation, characterization, and performance assessment of an innovative sensor for the rapid detection of organic residue levels and pH in water samples. The sensor is based on carbonaceous nanomaterials (CNMs) coated with an intrinsically conductive polymer, polyaniline (PANI). Inverse emulsion polymerizations of aniline in the presence of carbon nanotubes (CNTs) or graphene were prepared and confirmed by thermogravimetric analysis and high-resolution scanning electron microscopy. Aminophenol and phenol were used as proxies for organic residue detection. The PANI/CNM nanocomposites were used to fabricate thin-film sensors. Of all the CNMs, the smallest limit of detection (LOD) was achieved for multi-walled CNT (MWCNT) with a LOD of 9.6 ppb for aminophenol and a very high linearity of 0.997, with an average sensitivity of 2.3 kΩ/pH at an acid pH. This high sensor performance can be attributed to the high homogeneity of the PANI coating on the MWCNT surface.