ResumenPara optimizar el flujo vehicular en una intersección vial se diseñaron un algoritmo de control adaptativo y una base de datos que apoya la depuración del rendimiento del controlador, ambos alojados en el sistema embebido Raspberry Pi B+. El desempeño del algoritmo fue evaluado con un instrumento virtual, que emuló una intersección semafórica de la ciudad de Cúcuta, esto es, los sensores magnetorresistivos, el proceso de encendido en las luces de los semáforos y el flujo vehicular. La manipulación de los tiempos de encendido en las luces de los semáforos, aumentó el flujo vehicular hasta 5.5 % y, disminuyó el tiempo máximo de espera del vehículo para avanzar hasta 28 segundos y el largo de fila hasta un 18 %. Con base en el

This paper presents the analysis of a wavelength division multiplexer communication system in the frequency domain, with the objective of visualizing the incidence of the linear phenomena of attenuation and chromatic dispersion, together with the phenomenon of phase self-modulation, the Kerr electro-optical effect and fourth wave mixing. The analyzed system consists of a laser transmitter with a Mach-Zender modulator and a standard G.625b single-mode fiber link transmitting three optical signals of 10 mW, 25 mW and 50 mW at a fundamental wavelength of 1550 nm at a rate of 10 Gbps. This system is analyzed through a graphical user interface programmed by the authors in the Python environment, which calculates the parameters corresponding to each phenomenon and graphically represents the transmission results at distances of 50 km and 100 km. The analysis methodology consists of varying the spectral separation of the transmitted channels, initially considering a spectral separation of 2 nm and subsequently a spectral separation of 0.2 nm, observing as a result that the harmonics generated by the fourth wave mixing phenomenon considerably alter the spectral density of the transmitted signals, since the energy of the harmonics is equal to the power of the transmitted signals. On the other hand, with the spectral spacing of 0.2 nm, it is obtained that, although the harmonics alter the spectral density waveform, the bandwidth is not compromised by these additional signals.

The document shows the application of the empirical Angström-Prescott model in different places in Norte de Santander, Colombia. The model estimates solar radiation from hours of sunlight, at a site where brightness and solar radiation are measured. The data were obtained from the Institute of Hydrology, Meteorology and Environmental Studies, IDEAM; algorithms were developed in RStudio to process and analyze the information. The model establishes a linear relationship between solar radiation and the hours of sunlight, in a specific geographic location. Therefore, regression analyzes were performed for three different sites, using historical records of brightness and solar radiation, obtaining the R-squared coefficients of: 0.73, 0.78, and 0.42. The models were then extrapolated to nearby regions with solar brightness records, but without solar radiation data, to obtain an estimate of radiation at these locations. Finally, a database was created with monthly average information on solar radiation for various subregions of Norte de Santander, which can be used for the design and implementation of photovoltaic systems.

Resumen: El presente trabajo se implementa un controlador resonante integral para la atenuación del primer modo de vibración de una estructura flexible tipo viga en voladizo. El controlador se implementa mediante un circuito electrónico analógico y se u tilizan actuadores piezoeléctricos. Se presenta el proceso de acondicionamiento de la señal de aceleración utilizada, la sintonización del controlador y finalmente se exponen los resultados obtenidos experimentalmente, donde se observa una disminución en e l tiempo de estabilización superior al 50% con respecto al tiempo del sistema no controlado.Palabras clave: Control resonante, viga en voladizo, control activo de vibraciones. Abstract:In this job is implemented an integral resonant controller to att enuate the first vibration mode of a flexible structure type cantilever. The controller is implemented using an analog electronic circuit and use piezoelectric actuators. It presents the signal conditioning used, the tuning of the controller and finally it exposes the results obtained experimentally, where it can be seen a reduction in the stabilization time above 50% with respect to the non controlled system.

This article presents a computer tool that allows to carry out a mathematical analysis of the physical stability of the bipolar transistor in the design of amplifiers. The tool allows to introduce the values of voltage gain, output impedance and input impedance, current gain of transistors and power supplies, to give as a result the values of the resistances. It also allows modifying the transistor operating point and graphing in real time the behavior of the load line and the output signal of the amplifier. Different designs were made with the tool and the results obtained were compared with academic software approved by the scientific community. The errors in all variables evaluated were less than 1.5%. The results are important for semiconductor physics, taking into account that they reaffirmed the directly proportional relationship between the stability of the transistor in its amplification state and the power required to operate. Finally, we conclude that the computer tool allows us to design amplifiers with bipolar transistors with precision and, depending on the need or application of the amplifier, the operating point Q is located in the load line to obtain an output signal without distortion and with the least power dissipation.