Providing better fuel flexibility for future gas turbine generations is a challenge as the fuel range is expected to become significantly wider (natural gas, syngas, etc.). The technical problem is to reach a wide operational window, regarding both operational safety and low emissions. In a previous paper, an approach to meet these requirements has already been presented. However, in this previous study it was difficult to exactly quantify the improvement in operational safety due to the fact that the flashback phenomena observed were not fully understood. The present continuative paper is focused on a thorough investigation of operational safety also involving the influence of pressure on flashback and the emissions of the proposed burner concept. To gain better insight into the character of the propagation and to visualize the path of the flame during its upstream motion, tests were done on an atmospheric combustion test rig providing almost complete optical access to the mixing section as well as the flame tube. OH* chemiluminescence, HS-Mie scattering and ionization detectors were applied and undiluted H2 was used as fuel for the detailed analysis. To elaborate on the influence of pressure on the stability behavior, additional tests were conducted on a pressurized test rig using a downscaled burner. OH* chemiluminescence, flashback and lean blow out measurements were conducted in this campaign, using CH4, CH4/H2 mixtures and pure H2. The conducted experiments delivered the assets and drawbacks of the fuel injection strategy, where high axial fuel momentum was used to tune the flow field to achieve better flashback resistance.

Due to the expected increase in available fuel gas variants in the future and the interest in independence from a specific fuel, fuel flexible combustion systems are required for future gas turbine applications. Changing the fuel used for lean premixed combustion can lead to serious reliability problems in gas turbine engines caused by the different physical and chemical properties of these gases. A new innovative approach to reach efficient, safe, and low-emission operation for fuels such as natural gas, syntheses gas, and hydrogen with the same burner is presented in this paper. The basic idea is to use the additionally available fuel momentum of highly reactive gases stemming from their lower Wobbe index (lower volumetric heating value and density) compared with lowly reactive fuels. Using fuel momentum opens the opportunity to influence the vortex dynamics of swirl burners designed for lowly reactive gases in a favorable way for proper flame stabilization of highly reactive fuels without changing the hardware geometry. The investigations presented in this paper cover the development of the optimum basic aerodynamics of the burner and the determination of the potential of the fuel momentum in water channel experiments using particle image velocimetry. The results show that proper usage of the fuel momentum has enough potential to adjust the flow field to different fuels and their corresponding flame behavior. As the main challenge is to reach flashback safe fuel flexible burner operation, the main focus of the study lies on avoiding combustion induced vortex breakdown. The mixing quality of the resulting injection strategy is determined by applying laser induced fluorescence in water channel tests. Additional OH∗ chemiluminescence and flashback measurements in an atmospheric combustion test rig confirm the water channel results for CH4, CH4/H2 mixtures, H2 with N2 dilution, and pure H2 combustion. They also indicate a large operating window between flashback and lean blow out and show expected NOx emission levels. In summary, it is shown for a conical four slot swirl generator geometry that the proposed concept of using the fuel momentum for tuning of the vortex dynamics allows aerodynamic flame stabilization for different fuels in the same burner.

Due to the expected increase in available fuel gas variants in the future and the interest in independence from a specific fuel, fuel flexible combustion systems are required for future gas turbine applications. Changing the fuel used for lean premixed combustion can lead to serious reliability problems in gas turbine engines caused by the different physical and chemical properties of these gases. A new innovative approach to reach efficient, safe and low-emissions operation for fuels like natural gas, syntheses gas and hydrogen with the same burner is presented in this paper. The basic idea is to use the additionally available fuel momentum of highly reactive gases stemming from their lower Wobbe index (lower volumetric heating value and density) compared to lowly reactive fuels. Using fuel momentum opens the opportunity to influence the vortex dynamics of swirl burners designed for lowly reactive gases in a favorable way for proper flame stabilization of highly reactive fuels without changing the hardware geometry. The investigations presented in the paper cover the development of the optimum basic aerodynamics of the burner and the determination of the potential of the fuel momentum in water channel experiments using particle image velocimetry (PIV). The results show that a proper usage of the fuel momentum has enough potential to adjust the flow field to the different fuels and their corresponding flame behavior. As the main challenge is to reach flashback safe fuel flexible burner operation, the main focus of the study lies on avoiding combustion induced vortex breakdown (CIVB). The mixing quality of the resulting injection strategy is determined applying laser induced fluorescence (LIF) in water channel tests. Additional OH* chemiluminescence and flashback measurements in an atmospheric combustion test rig confirm the water channel results for CH4, CH4/H2 mixtures, H2 with N2 dilution and pure H2 combustion. They also indicate a large operating window between flashback and lean blow out and show expected NOx emission levels. In summary, it is shown for a conical four slot swirl generator geometry that the proposed concept of using the fuel momentum for tuning of the vortex dynamics allows aerodynamic flame stabilization for different fuels in the same burner.

An experimental study is presented on the interaction of flashback originating from flame propagation in the boundary layer (1), from combustion driven vortex breakdown (2) and from low bulk flow velocity (3). In the investigations, an aerodynamically stabilized swirl burner operated with hydrogen-air mixtures at ambient pressure and with air preheat was employed, which previously had been optimized regarding its aerodynamics and its flashback limit. The focus of the present paper is the detailed characterization of the observed flashback phenomena with simultaneous high speed PIV/Mie imaging, delivering the velocity field and the propagation of the flame front in the mid plane, in combination with line-of-sight integrated OH*-chemiluminescence detection revealing the flame envelope and with ionization probes which provide quantitative information on the flame motion near the mixing tube wall during flashback. The results are used to improve the operational safety of the system beyond the previously reached limits. This is achieved by tailoring the radial velocity and fuel profiles near the burner exit. With these measures the resistance against flashback in the center as well as in the near wall region is becoming high enough to make turbulent flame propagation the prevailing flashback mechanism. Even at stoichiometric and preheated conditions this allows safe operation of the burner down to very low velocities of approx. 1/3 of the typical flow velocities in gas turbine burners. In that range the high turbulent burning velocity of hydrogen approaches the low bulk flow speed and, finally, the flame begins to propagate upstream once turbulent flame propagation becomes faster than the annular core flow. This leads to the conclusions that finally the ultimate limit for the flashback safety was reached with a configuration, which has a swirl number of approx. 0.45 and delivers NOx-emissions near the theoretical limit for infinite mixing quality, and that high fuel reactivity does not necessarily rule out large burners with aerodynamic flame stabilization by swirling flows.

The paper describes the development and validation of an efficient and cost effective method for the prediction of the NOx emissions of turbulent gas turbine burners in the early burner design phases, which are usually focused on the optimization of the swirler aerodynamics and the fuel-air mixing. Since the method solely relies on nonreacting tests of burner models in the water channel, it can be applied before any test equipment for combustion experiments exists. In order to achieve optimum similarity of fuel-air mixing in the water channel tests with engine operation the model is operated at the engine momentum ratio. During the laser induced fluorescence (LIF) measurements the water flow representing the fuel is doped with fluorescent dye, a plane perpendicular to the length axis near the burner exit plane is illuminated with a 5W Ar-ion laser, and the fluorescence is recorded with a video camera from downstream. From the video sequence,s the local probability density functions (PDF) of the dye concentration fluctuations are calculated from the data. Furthermore, the time mean velocity fields are measured with particle image veiocimetry (PIV). The PDF s of the local equivalence ratio are derived from the LIF data. Assuming flamelets, the NO^ generation in the entire equivalence ratio range observed in the water channel tests is computed using the unstrained freely propagating one-dimensional flame model in Cantera and the GRI3.0 reaction scheme. Although neither flame stretch nor post flame NO^ generation were considered, the computed NOx values were in excellent agreement with the experimental data from perfectly premixed combustion experiments. The local time averaged NO^ mole fraction is obtained by integrating the flamelet NO^ over the mixture PDF. Finally the global NO y emission of the burner at the considered operating point is obtained by spatial integration, considering the measured velocity field. The method was validated using a conical swirl burner with two fuel injection stages, allowing the degree of premixedness to be adjusted over a wide range, depending on the specific fuel injection scenario. For the case with fuel injection along the air inlet slots NO^ values slightly above the minimum NOx limit for perfectly premixed combustion were computed. This is consistent with the emission measurements and indicates the finite mixing quality of this injection method. In the partially premixed regime the configurations with potential for low NOx emissions were reliably identified with the LIF and PIV based water channel method. The method also shows the steep increase of the NOx emissions with the decreasing degree ofpremixing observed in the experiments, however, quantitative predictions would have required a postprocessing of the data from the LIF mixing study with a higher spatial resolution than available.