This contribution aims to improve existing scalings of the L-mode power decay length λ q o m p , especially for plasma configurations with strike points at the ITER-relevant location—closed vertical divertor targets. We propose 13 new λ q o m p scalings based on data from the tokamaks JET, EAST, MAST, Alcator C-mod and COMPASS, and validate them against the output of the 2D turbulence code HESEL. The analysis covers 500 divertor heat flux profiles (obtained by probes or IR cameras), measured in L-mode discharges with varying 12 global plasma parameters (all well predictable). We find that the two previously published scalings (Eich 2013 J. Nucl. Mat. 438 S72) and (Scarabosio 2013 J. Nucl. Mat. 438 S426), which were based on outer target data from AUG and JET, describe the JET, C-mod and COMPASS profiles well. This holds not only at the outer horizontal and vertical targets, but surprisingly also at the inner vertical targets. In contrast, EAST, HESEL and especially MAST data are poorly described by these two scalings. We therefore derive 13 new scalings, which account for 85–92 % of the measured λ q o m p variability across all five tokamaks. Although each of the scalings is based on a different parameter combination, their predictions for the ITER and COMPASS-Upgrade tokamaks are very similar. Just before the L-H transition in the ITER baseline scenario, the presented scalings predict values λ q o m p = 3.0 ± 0.5 mm. For the COMPASS-Upgrade tokamak, all the scalings predict λ q o m p = 2.1 ± 0.5 mm with a single exception of the scaling based on the stored plasma energy which predicts only 1.2 mm for both tokamaks. We encourage the reader to use as many of these scalings as possible, depending on available data. In attached plasma and using significant assumptions, our results imply steady-state surface-perpendicular heat flux around 10 MW/m2 for ITER, and 20 MW/m2 for COMPASS-Upgrade.

Plasma Phys. Control. Fusion 58 (2016) 074005 (11pp) q imp mm, thus consolidating the 50 mm width used to optimize the FW panel toroidal shape.

A new system of probes was recently installed in the divertor of tokamak COMPASS in order to investigate the ELM energy density with high spatial and temporal resolution. The new system consists of two arrays of rooftop-shaped Langmuir probes (LPs) used to measure the floating potential or the ion saturation current density and one array of Ball-pen probes (BPPs) used to measure the plasma potential with a spatial resolution of ~3.5 mm. The combination of floating BPPs and LPs yields the electron temperature with microsecond temporal resolution. We report on the design of the new divertor probe arrays and first results of electron temperature profile measurements in ELMy Hmode and L-mode. We also present comparative measurements of the parallel heat flux using the new probe arrays and fast infrared termography (IR) data during L-mode with excellent agreement between both techniques using a heat power transmission coefficient γ = 7. The ELM energy density  || was measured during a set of NBI assisted ELMy H-mode discharges. The peak values of  || were compared with those predicted by model and with experimental data from JET, AUG and MAST with a good agreement.

This paper summarizes the status of the COMPASS tokamak, its comprehensive diagnostic equipment and plasma scenarios as a baseline for the future studies. The former COMPASS-D tokamak was in operation at UKAEA Culham, UK in 1992-2002. Later, the device was transferred to the Institute of Plasma Physics of the Academy of Sciences of the Czech Republic (IPP AS CR), where it was installed during 2006-2011. Since 2012 the device has been in a full operation with Type-I and Type-III ELMy H-modes as a base scenario. This enables together with the ITER-like plasma shape and flexible NBI heating system (two injectors enabling co-or balanced injection) to perform ITER relevant studies in different parameter range to the other tokamaks (ASDEX-Upgrade, DIII-D, JET) and to contribute to the ITER scallings. In addition to the description of the device, current status and the main diagnostic equipment, the paper focuses on the characterization of the Ohmic as well as NBIassisted H-modes. Moreover, Edge Localized Modes (ELMs) are categorized based on their frequency dependence on power density flowing across separatrix. The filamentary structure of ELMs is studied and the parallel heat flux in individual filaments is measured by probes on the outer mid-plane and in the divertor. The measurements are supported by observation of ELM and inter-ELM filaments by an ultra-fast camera.

 Users may download and print one copy of any publication from the public portal for the purpose of private study or research.  You may not further distribute the material or use it for any profit-making activity or commercial gain  You may freely distribute the URL identifying the publication in the public portal If you believe that this document breaches copyright please contact us providing details, and we will remove access to the work immediately and investigate your claim.