Recently, nanocarbons (carbon nanofibers (CNFs) and carbon nanotubes (CNTs)) have been used efficiently in numerous research works to significantly enhance the mechanical properties of composites. With their amazing mechanical properties and exceptionally high aspect ratios, nanocarbons (NCs) are seen as one of the most beneficial nanomaterials for nano-reinforcement. The dispersion of NCs is one of the key factors that strongly influence the properties of nanocomposites. Several researches have been carried out with chemical agents to achieve a consistent dispersal of carbon nanomaterials in water, although, if the process is uncontrolled, it can shorten or damage the NCs or even dissolve them, and this can have a negative effect on the composites as well. Therefore, if NCs are to be used as reinforcement for composites, physical methods have to be employed to disperse the NCs before they can be mixed into the composites. This paper presents an overview of the different types of NCs, their different uses and the research conducted for the dispersion of NCs by chemical and physical methods. Furthermore, a summary is given of the measurement and characterization of the dispersibility of NCs.

Soil stabilization, using a variety of stabilizers, is a common method used by engineers and designers to enhance the properties of soil. The use of nanomaterials for soil stabilization is one of the most active research areas that also encompass a number of disciplines, including civil engineering and construction materials. Soils improved by nanomaterials could provide a novel, smart, and eco-and environment-friendly construction material for sustainability. In this case, carbon nanomaterials (CNMs) have become candidates for numerous applications in civil engineering. The main objective of this paper is to explore improvements in the physical properties of UKM residual soil using small amounts (0.05, 0.075, 0.1, and 0.2%) of nanocarbons, that is, carbon nanotube (multiwall carbon nanotube (MWCNTs)) and carbon nanofibers (CNFs). The parameters investigated in this study include Atterberg's limits, optimum water content, maximum dry density, specific gravity, pH, and hydraulic conductivity. Nanocarbons increased the pH values from 3.93 to 4.16. Furthermore, the hydraulic conductivity values of the stabilized fine-grained soil samples containing MWCNTs decreased from 2.16 − 09 m/s to 9.46 − 10 m/s and, in the reinforcement sample by CNFs, the hydraulic conductivity value decreased to 7.44 − 10 m/s. Small amount of nanocarbons (MWCNTs and CNFs) decreased the optimum moisture content, increased maximum dry density, reduced the plasticity index, and also had a significant effect on its hydraulic conductivity.

No abstract

This paper presents the improvement of the unconfined compressive strength (UCS) of soil by mixing different percentages of nanolime and 5% lime with soil. The UCS of treated soil increased significantly over curing time with increasing percentage of nanolime. The optimum results were reached at only 0.5% nanolime admixtures which were much higher than 5% lime admixture. This may be due to higher ability of nanolime to flocculate and agglomerate the soil particles compared with the lime. In addition, the lime could fill only the micropores while nanolime could fill the micro-and nanopores as well. The strength gain is inversely proportional to the remolded moisture content and curing period. However, when the content of nanolime used is larger than 0.5%, nanolime particles are not uniformly dispersed. Therefore, a weak area in the form of voids is created, consequently the homogeneous hydrated microstructure cannot be formed, and finally the strength will decrease.

This article presents a comparative study of the behaviour of clayey soil reinforcements using stone column ground improvement by means of numerical analyses. Two-dimensional finite element analyses with commercially available software, PLAXIS, were performed on end-bearing stone columns using 15-noded triangular elements to investigate the impact of the modelling type on the stress concentration ratio and failure mechanism of an improved foundation system. Consolidation analyses were conducted throughout the study using Mohr-Coulomb’s criterion. The computed values of the stress concentration ratios were compared for different key parameters, including the diameters of stone columns, c/c spacing of columns, friction angle of stone column material, and undrained cohesion of soft soil. The major conclusions of this study were that the stone column in the unit cell model shared between 2.5 to 3.14 times more loads than the surrounding soil, whilst in the plane strain model it shared between 1.7 to 2.9 times more loads. The use of plane strain approach to model the stone column gave a more comprehensive representation of the stress distribution and load transfer between the soil and columns, in addition to being a better method than the unit cell concept to evaluate the failure mode in this system.