A large volume gamma spectrometer was designed and constructed to analyze foodstuffs and environmental samples having low radionuclide concentrations. This system uses eight 11-cm × 42.5-cm × 5.5-cm NaI(Tl) detectors, chosen due to their relatively high sensitivity and availability and arranged in an octagonal configuration. The sensitive volume of the system is ~28 cm in diameter and ~42 cm deep. Shielding consists of an 86-cm × 86-cm square, 64-cm-tall lead brick enclosure with 18-cm-thick lead walls lined by 0.3-cm-thick copper plates. An aluminum top was machined to suspend the detectors within this shield. The shielding reduces background counts by 72% at 100 keV and 42% at 1,000 keV. The positional variability in sensitivity of the well was determined by both simulation and experiment. A 2.1-L volume of nearly uniform sensitivity, varying less than 10%, exists in the well's center. Energy resolutions of 14.6% and 7.8% were measured for 241Am and 137Cs, respectively. Energy resolution shows a 0.2% variation for both 241Am and 137Cs as a function of position within all regions of the well’s central sensitive volume. Dead time was also determined to be less than 35% for all sources measured in the system, the largest of which had an activity of 1,760 kBq. Simulated results for various source geometries show higher counts for smaller samples, especially at lower energies due to less attenuation of low energy photons. Minimum detectable activities were determined for all source energies used, less than 5.1 Bq kg−1 for reasonable background and sample counting times.

Experiments were performed with 30 11 cm × 42.5 cm × 5.5 cm NaI(Tl) detectors to better understand their positional response. Spectra were collected using 0.02 to 0.15 MBq point sources of 241Am, 137Cs, 60Co, and 133Ba positioned on lines parallel and perpendicular to the long axis of the crystal along both the narrow and wide detector faces as well as at different distances from them. A greater density of positions was sampled at the ends of the detector, and repeated measurements were made to examine potential gain drifts during the experiment. Spectroscopic peak counts, spectroscopic pulse heights, and net counts were analyzed. Empirical equations were fit to the aforementioned data for each specific source energy as a function of source position. In addition, a Monte Carlo radiation transport code was used to simulate the expected positionally variable response based solely upon radiation absorption. The simulated radiation transport efficiency functions were compared to the experimental data. The effects of the geometric radiation efficiency, the attenuation and scattering of emitted light within the scintillation crystal, and combined effects such as nonuniformity of the photomultiplier tube, photocathode response, and crystal irregularities were then distinguished. Functions describing each effect were derived. The results suggest potential new corrections to data obtained with large scintillation detectors as well as a novel approach to partial positional gamma-ray detection with minimal collimation, given that the energy resolution is within reason for particular photopeaks.

Legacy Geiger-Muller (GM) survey meters recovered from fallout shelters have been used by several nuclear scientific societies as part of high school outreach programs. A donated antique instrument helps teachers demonstrate radiological principles, but fails to develop student's electronics skills, generate excitement for nuclear careers, or provide individuals with their own devices to explore the radioactive planet. A simple, affordable GM survey meter built by each student would increase direct engagement while providing hands-on experience with circuit-building, soldering, and computer programming. The inclusion of an affordable single-board computer as a component in the survey meter would enable students to tackle more various computer science and electronics projects, thereby potentially recruiting more students into technology and engineering. This paper details the challenges faced by an interdisciplinary undergraduate team designing an easy-to-assemble smart GM survey meter. Their iterative research, design, and testing process included modification to a basic circuit to enable use of different tube types, component cost reduction, application development, and data communication. The ultimate product of the team's efforts, a survey meter with affordable components and a smartphone application capable of creating radiation maps, is detailed in full.