Inspired by the transparent hair layer on water plants Salvinia and Pistia, superhydrophobic flexible thin films, applicable as transparent coatings for optoelectronic devices, are introduced. Thin polymeric nanofur films are fabricated using a highly scalable hot pulling technique, in which heated sandblasted steel plates are used to create a dense layer of nano- and microhairs surrounding microcavities on a polymer surface. The superhydrophobic nanofur surface exhibits water contact angles of 166 ± 6°, sliding angles below 6°, and is self-cleaning against various contaminants. Additionally, subjecting thin nanofur to argon plasma reverses its surface wettability to hydrophilic and underwater superoleophobic. Thin nanofur films are transparent and demonstrate reflection values of less than 4% for wavelengths ranging from 300 to 800 nm when attached to a polymer substrate. Moreover, used as translucent self-standing film, the nanofur exhibits transmission values above 85% and high forward scattering. The potential of thin nanofur films for extracting substrate modes from organic light emitting diodes is tested and a relative increase of the luminous efficacy of above 10% is observed. Finally, thin nanofur is optically coupled to a multicrystalline silicon solar cell, resulting in a relative gain of 5.8% in photogenerated current compared to a bare photovoltaic device.

To unleash the full potential of white organic light-emitting diodes (OLEDs) as large-area light sources, guided optical modes have to be efficiently outcoupled, which calls for internal extraction layers (IELs) that can be easily integrated into a scalable manufacturing process. To realize such IELs, we developed a high refractive index scattering polymer:TiO2-nanoparticle mixture that can be deposited onto a large area by using the cost-effective screen-printing method. We exploited this approach to produce a 10 μm thick IEL covering the exact area of active pixels distributed over a 15 × 15 cm2 glass substrate. By optimizing the initial mixture composition, we achieved screen-printing-compatible rheological properties as well as tailored light scattering and transmission over the visible spectrum. The spatial homogeneity of those optical properties was obtained by additional substrate treatments to improve the wetting behavior and to allow reflow after printing. The devices were finalized by depositing a high-efficiency white OLED stack atop the IEL. We demonstrated a luminous efficacy increase up to 56% due to the scattering layer. The IEL also ensured a Lambertian emission profile without any angular color shift.

White organic light emitting diodes (WOLEDs) suffer from poor outcoupling efficiencies. The use of Bragg-gratings to enhance the outcoupling efficiency is very promising for light extraction in OLEDs, but such periodic structures can lead to angular or spectral dependencies in the devices. Here we present a method which combines highly efficient outcoupling by a TiO 2 -Bragg-grating leading to a 104% efficiency enhancement and an additional high quality microlens diffusor at the substrate/air interface. With the addition of this diffusor, we achieved not only a uniform white emission, but also further increased the already improved device efficiency by another 94% leading to an overall enhancement factor of about 4.

To allow a greater acceptance in the display and lighting markets, organic lightemitting diode (OLED) technology is currently the subject of intensive research efforts aimed at manufacturing cost-effective devices with higher efficiencies. In this regard, strategies matured in the field of photonics and nanophotonics can be applied for photon management purposes to improve the outcoupling of the generated light and to control the emission pattern. In this review, we report on the recent experimental and numerical advances to pursue those goals by highlighting the example of bottom-emitting devices. The cases of periodical microand nanostructures, as well as of stochastic ensembles that can be easily implemented using printing techniques, are covered herein. It is shown that beyond the sole optical properties, such additional elements can simultaneously improve the electrical characteristics of solutionprocessed OLEDs, and thus enable an optimization of the devices at different levels. © The Authors. Published by SPIE under a Creative Commons Attribution 3.0 Unported License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.

In this work, we have improved the absorption properties of thin film solar cells by introducing light trapping reflectors deposited onto self-assembled nanostructures. The latter consist of a disordered array of nanopillars and are fabricated by polymer blend lithography. Their broadband light scattering properties are exploited to enhance the photocurrent density of thin film devices, here based on hydrogenated amorphous silicon active layers. We demonstrate that these light scattering nanopillars yield a short-circuit current density increase of +33%rel with respect to equivalent solar cells processed on a planar reflector. Moreover, we experimentally show that they outperform randomly textured substrates that are commonly used for achieving efficient light trapping. Complementary optical simulations are conducted on an accurate 3D model to analyze the superior light harvesting properties of the nanopillar array and to derive general design rules. Our approach allows one to easily tune the morphology of the self-assembled nanostructures, is up-scalable and operated at room temperature, and is applicable to other photovoltaic technologies.