The global aim of the theme of magnesium alloy processing by the selective laser melting technology is to enable printing of replacements into the human body. By combining the advantages of WE43 magnesium alloy and additive manufacturing, it is possible to print support structures that have very similar properties to human bones. However, printing magnesium alloy parts is very difficult, and the printing strategies are still under development. Knowledge of weld deposit behaviour is needed to design a complex printing strategy and still missing. The main aim of the manuscript is the find a stable process window and identify the dependence of the weld deposit shape and properties on the laser power and scanning speed. The range of the tested parameters was 100–400 W and 100–800 mm/s for laser power and scanning speed. The profilometry and light microscopy were used to verify the continuity and shape evaluation. The microhardness and EDX analysis were used for the detailed view of the weld deposit. The manuscript specifies the weld deposit dimensions, their changes depending on laser power and scanning speed, and the continuity of the weld tracks. The stable weld deposits are made by the energy density of 5.5–12 J/mm2. Thin walls were also created by layering welds to determine the surface roughness scattering (Ra 35–60) for various settings of laser power and scanning speed.

No abstract

In this work, selective laser melting (SLM) technology was used to prepare Mg-4Y-3Nd-Zr (WE43) alloy. This alloy and production method are promising for the design of biodegradable implants. The aim of this study was to investigate the chemical composition, microstructure, mechanical properties, corrosion behavior in simulated body fluid (SBF), and cytotoxicity of the alloy produced by SLM method and to compare it with conventionally gravity cast reference alloy. Analysis of the surface of the revealed an oxygen content of 7 wt.%. Undesirable unmelted and only partially adhered spherical particles of the starting powder were also found. The microstructure of the material was very fine and consisted of α-Mg dendritic matrix, β-Mg41(Nd, Y)5 intermetallic phase, Y2O3 inclusions, and 0.6 vol.% of residual porosity. The Vickers hardness, compressive yield strength, compressive strength, and maximum compressive strain were 88 HV0.1, 201 MPa, 394 MPa, and 14%, respectively, which are close to the reference values in as-cast. The in vitro corrosion rates determined by immersion and potentiodynamic tests were 2.6 mm/year and 1.3 mm/year, respectively. Cytotoxicity tests indicated good biocompatibility of the 3D-printed alloy.

Additive manufacturing of Al-alloys allows the production of components with a complicated structured shape, geometry composed by lattice structures, internal cooling, etc. The portfolio of Al-alloys for metal additive manufacturing is still under development and is strongly limited, compared to the conventional technology. The alloy AlSi9Cu3 is used in many applications, but its processing details are still missing. The main aim of this paper is to describe the laser process parameters for AlSi9Cu3, processed by SLM technology and manufactured from two powders of different shapes and particle sizes. The tested process parameters were laser power, laser speed, and hatch distance in the range of 100-400 W, 200-1500 mm • s −1 and 90-150 µm. These were tested using a single-track and cube test. Microstructure, mechanical properties and the fatigue of SLM samples were analysed and compared with as-casted material.

This paper reports on the influence of production parameters on the properties of 3D printed magnesium alloy Mg-4Y-3RE-Zr (WE43) produced by the selective laser melting method. We present microstructures and mechanical properties of four selected samples prepared under various production parameters. Optical and scanning electron microscopy together with energy-dispersive X-ray spectrometry were used for microstructure analysis. Porosity was evaluated based on image analysis. To represent differences in mechanical properties, microhardness measurement and compression tests were performed. Based on our observations of microstructure quality and performed tests, the results of the parameter impact study are further applied to the production of products of the required quality.