A number of recent studies have demonstrated the effectiveness of atomic force microscopy (AFM) for characterization of cellular stress-relaxation behavior. However, this technique's recent development creates considerable need for exploration of appropriate mechanical models for analysis of the resultant data and of the roles of various cytoskeletal components responsible for governing stress-relaxation behavior. The viscoelastic properties of vascular smooth muscle cells (VSMCs) are of particular interest due to their role in the development of vascular diseases, including atherosclerosis and restenosis. Various cytoskeletal agents, including cytochalasin D, jasplakinolide, paclitaxel, and nocodazole, were used to alter the cytoskeletal architecture of the VSMCs. Stress-relaxation experiments were performed on the VSMCs using AFM. The quasilinear viscoelastic (QLV) reduced-relaxation function, as well as a simple power-law model, and the standard linear solid (SLS) model, were fitted to the resultant stress-relaxation data. Actin depolymerization via cytochalasin D resulted in significant increases in both rate of relaxation and percentage of relaxation; actin stabilization via jasplakinolide did not affect stress-relaxation behavior. Microtubule depolymerization via nocodazole resulted in nonsignificant increases in rate and percentage of relaxation, while microtubule stabilization via paclitaxel caused significant decreases in both rate and percentage of relaxation. Both the QLV reduced-relaxation function and the power-law model provided excellent fits to the data (R(2)=0.98), while the SLS model was less adequate (R(2)=0.91). Data from the current study indicate the important role of not only actin, but also microtubules, in governing VSMC viscoelastic behavior. Excellent fits to the data show potential for future use of both the QLV reduced-relaxation function and power-law models in conjunction with AFM stress-relaxation experiments.

It was hypothesized that supercritical carbon dioxide (SC-CO(2)) treatment could serve as an alternative sterilization method at various temperatures (40-105 degrees C), CO(2) pressures (200-680 atm), and treatment times (25 min to 6 h), and with or without the use of a passive additive (distilled water, dH(2)O) or an active additive (hydrogen peroxide, H(2)O(2)). While previous researchers have shown that SC-CO(2) possesses antimicrobial properties, sterilization effectiveness has not been shown at sufficiently low treatment temperatures and cycle times, using resistant bacterial spores. Experiments were conducted using Geobacillus stearothermophilus and Bacillus atrophaeus spores. Spore strips were exposed to SC-CO(2) in commercially available supercritical fluid extraction and reaction systems, at varying temperatures, pressures, treatment times, and with or without the use of a passive additive, such as dH(2)O, or an active additive, such as H(2)O(2). Treatment parameters were varied from 40 to 105 degrees C, 200-680 atm, and from 25 min to 6 h. At 105 degrees C without H(2)O(2), both spore types were completely deactivated at 300 atm in 25 min, a shorter treatment cycle than is obtained with methods in use today. On the other hand, with added H(2)O(2) (<100 ppm), 6 log populations of both spore types were completely deactivated using SC-CO(2) in 1 h at 40 degrees C. It was concluded from the data that large populations of resistant bacterial spores can be deactivated with SC-CO(2) with added H(2)O(2)at lower temperatures and potentially shorter treatment cycles than in most sterilization methods in use today.

No abstract

Vascular smooth muscle cell (VSMC) function plays a key role in regulating the development and progression of vascular lesions. Among the more significant phenomena that occur during the development of these lesions is the phenotypic switching of VSMCs from a contractile to a synthetic state. A better understanding of the concurrent changes to VSMC mechanical properties that occur with phenotypic shifts can help to elucidate the role of VSMC mechanics in the development of vascular diseases. In the current study, the mechanical properties of adherent cultured rat aortic VSMCs were assessed by atomic force microscopy. Serum starvation was used to induce a phenotypic shift in vitro. It was concluded that serum starvation led to a statistically significant increase in apparent elastic modulus after 5 days, as well as a statistically significant decrease in hysteresis after culture for 3 days. If this trend of VSMC mechanical properties changing concurrently with phenotypic shifts were to hold true in vivo, such changes could affect the processes of mechanotransduction and/or arterial mechanical properties, thereby contributing to the progression of vascular disease.

With the advancement of the field of biotribology, considerable interest has arisen in the study of cell and tissue frictional properties. From the perspective of medical device development, the frictional properties between a rigid surface and underlying cells and tissues are of a particular clinical interest. As with many bearing surfaces, it is likely that contact asperities exist at the size scale of single cells and below. Thus, a technique to measure cellular frictional properties directly would be beneficial from both a clinical and a basic science perspective. In the current study, an atomic force microscope (AFM) with a 5 μm diameter borosilicate spherical probe simulating endovascular metallic stent asperities was used to characterize the surface frictional properties of vascular smooth muscle cells (VSMCs) in contact with a metallic endovascular stent. Various treatments were used to alter cell structure, in order to better understand the cellular components and mechanisms responsible for governing frictional properties. The frictional coefficient of the probe on VSMCs was found to be approximately 0.06. This frictional coefficient was significantly affected by cellular crosslinking and cytoskeletal depolymerization agents. These results demonstrate that AFM-based lateral force microscopy is a valuable technique to assess the friction properties of individual single cells on the micro-scale.