The effects of powder formulation, including elemental mixed powder (EMP) and alloy mixed powder (AMP), and energy density on the nitrogen content and microstructural characteristics of high-nitrogen steel prepared by selective laser melting were investigated. The results reveal that the samples prepared with EMP had more nonfusion flaws and a relatively low density, with a maximum of only 92.36%, while samples prepared with AMP had fewer defects and a relative density of up to 97.21%. The nitrogen content and microstructural characteristics were significantly influenced by the laser energy density. The relative density of the EMP samples increased from 88.29% to 92.36% as the laser energy density increased from 83.3 J/mm3 to 125 J/mm3, while the relative density of the AMP samples rose from 93.31% to 97.21%, and the number of defects and the nitrogen content decreased. The mechanical properties of the AMP samples were superior to those of the EMP samples when the energy density rose, and the strength of the high-nitrogen steel first rose and then fell. The AMP samples showed the best mechanical properties when the energy density was 104.2 J/mm3, which corresponds to a laser power of 250 W, a scanning speed of 1000 mm/s, and a layer thickness of 30 μm. The corresponding values of yield strength, ultimate tensile strength, and elongation were 958.8 MPa, 1189.2 MPa, and 30.66%, respectively.

High-nitrogen stainless steels are widely used due to their excellent comprehensive performance. In this study, the effects of process parameters (laser power, scanning speed, and cavity pressure) on the formation of high-nitrogen stainless steels were studied by using conventional selective laser melting and high-pressure selective laser melting (HPSLM). The nitrogen content, nitrogen emission, phase composition, microstructure, and microhardness of the high-nitrogen stainless steel samples obtained through selective laser melting (SLM) were analysed by using an oxygen/nitrogen/hydrogen analyser, X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and electron backscatter diffraction. The results showed that the maximum nitrogen emission in the SLM sample was 0.175 wt.%, the emission rate reached up to 54.7%, and the maximum nitrogen content in the HPSLM sample was 1.07 wt.%. There was no significant difference between the phase peak positions of the SLM samples with different laser powers and the original powder. The main phase of the HPSLM sample changed at 0.3 MPa (from α-Fe to γ-Fe phase); the microstructure of the SLM sample was mainly composed of columnar and cellular crystals, and columnar crystal bands formed along the direction of heat flow. The HPSLM sample was mainly composed of equiaxed crystals with a grain size of 10–15 μm. At an energy density of 136 J/mm3, the microhardness and relative density reached their peak values of 409 HV and 98.85%, respectively.

Chromium nitride powder is blended with pre-alloyed powder to make an overmatched powder with a high nitrogen concentration in order to manufacture high-nitrogen steel by selective laser melting. By employing a wider range of process parameters, the impact of process parameters on the relative density, nitrogen concentration, microstructure, and mechanical properties of high-nitrogen steel is investigated. In simulated human body fluid conditions, the corrosion resistance of high-nitrogen steel, pure titanium, and 316L was compared and evaluated. The findings demonstrate that the relative density of high-nitrogen steel initially rises and then falls with the increase in energy density, reaching a high value of 98.8% at 148.8 J/mm3. With rising energy density, the nitrogen concentration falls. The microstructure of high-nitrogen steel is mainly composed of columnar and cellular grains. Both grain sizes steadily grow, but their mechanical characteristics initially rise and then fall as the energy density rises from 83.3 to 187.3 J/mm3. With yield strength, tensile strength, and elongation reaching 921.9 MPa, 1205.1 MPa, and 27%, respectively, the alloy exhibits outstanding mechanical characteristics when the laser power is 250 W, the scanning speed is 700 mm/s, and the associated energy density is 148.8 J/cm3. The high-nitrogen steel at an energy density of 148.8 J/mm3 has the lowest corrosion rate when compared to pure titanium and 316L steel, which suggests that the HNS alloy will have good corrosion resistance in human body fluid conditions.

No abstract

No abstract