Nanofiber mats produced by electrospinning, with the advantages of specific surface area, porosity and chemical tenability, are an ideal support material for deposition of metal[Formula: see text]organic framework (MOF) crystals. In this study, four types of MOFs (MIL-53(Al), ZIF-8, UiO-66-NH2 and NH2-MIL-125(Ti)) were deposited on polydopamine (PDA)-modified electrospun polyvinyl alcohol (PVA)/SiO2 organic[Formula: see text]inorganic hybrid nanofiber mats by bulky synthesis. Because of the formation of Si–O–C–O–Si bridges between PVA chains and silica network, electrospun PVA/SiO2 organic[Formula: see text]inorganic hybrid nanofiber mats are quite stable in water or organic solvents and at high temperature are suitable as supports for MOFs deposition. The PDA layer, which exhibits a powerful adhesive ability to attach foreign objects, can effectively improve growth of MOFs on the surface of PVA/SiO2 nanofiber mats. The obtained MOF composites combining the unique properties of electrospun nanofibers mats and MOFs particles become flexible and tailorable, greatly expanding the application range of MOFs materials. The synthesized MOF composites were used to adsorb chloramphenicol (CAP) in water. It was found that the four MOF composites could remove CAP from water effectively and MIL-53(Al) composite had the highest adsorption capacity due to the higher specific surface area.

No abstract

A surface acoustic wave (SAW) formaldehyde gas sensor was fabricated on a 42°75' ST-cut quartz substrate, with a composite sensing layer of zeolitic imidazolate framework (ZIF)-8 on polyethyleneimine (PEI)/ bacterial cellulose (BC) nanofilms. The addition of snowflake-like ZIF-8 structure on the PEI/BC sensitive film significantly improves the hydrophobicity of the SAW sensor and increases the sensor's sensitivity to formaldehyde gas. It also significantly increases the surface roughness of the sensitive film. Its hydrophobic nature prevents water molecules from entering into the internal pores of the BC film, thereby avoiding significant mass loading caused by the humidity change when the sensor is used to detect low-concentration formaldehyde gas. The Zn2+ sites at the surface of ZIF-8 improves the sensor's response to formaldehyde gas through enhancing the physical adsorptions. Experimental results show that the ZIF-8@PEI/BC SAW sensor has a response (e.g., frequency shift) of 40.3 kHz to 10 ppm formaldehyde gas at 25℃ and 30% RH. When the relative humidity was increased from 30% to 93%, the response (frequency shift) of the sensor drifts only ~5%, and there is negligible drift at a medium humidity level (~56% RH).

Hollow inorganic nanofibers have great potential application in the field of photocatalysis due to their special three-dimensional structure. In our work, we have fabricated ZnO hollow nanofibers (ZnO-HNF) by simple single-spinneret electrospinning of polyacrylonitrile (PAN)/zinc acetate precursor solution, followed by stepwise annealing at 300–500 °C. The results show that long and continuous ZnO-HNF with shell consisting of uniform compacted ZnO nanoparticles are successfully fabricated, and the shell thickness is approximately 30 nm. The formation mechanism of ZnO-HNF is speculated to be consequence of the different rate of mass diffusion during the annealing process (Kirkendall effect). The prepared Zn-HNF exhibits good performance in photocatalysis. The photocatalytic removal efficiency of Rhodamine B (RhB) under ultraviolet light irradiation can reach 94.08% in 1 hour, and the removal efficiency of Cr(VI) is 94.49% in 2 hours. This work provides new ideas for the development of ZnO in the field of photocatalysis, and provides new possibilities for more types of subsequent photocatalytic materials.