Single-walled carbon nanotube (SWNT) thin film electrodes have been printed on flexible substrates and cloth fabrics by using SWNT inks and an off-the-shelf inkjet printer, with features of controlled pattern geometry (0.4-6 cm 2 ), location, controllable thickness (20-200 nm), and tunable electrical conductivity. The as-printed SWNT films were then sandwiched together with a piece of printable polymer electrolyte to form flexible and wearable supercapacitors, which displayed good capacitive behavior even after 1,000 charge/discharge cycles. Furthermore, a simple and efficient route to produce ruthenium oxide (RuO 2 ) nanowire/SWNT hybrid films has been developed, and it was found that the knee frequency of the hybrid thin film electrodes can reach 1,500 Hz, which is much higher than the knee frequency of the bare SWNT electrodes (~158 Hz). In addition, with the integration of RuO 2 nanowires, the performance of the printed SWNT supercapacitor was significantly improved in terms of its specific capacitance of 138 F/g, power density of 96 kW/kg, and energy density of 18.8 Wh/kg. The results indicate the potential of printable energy storage devices and their significant promise for application in wearable energy storage devices.

In the past, the electrochemical instability of III–V semiconductors has severely limited their applicability in photocatlaysis. As a result, a vast majority of the research on photocatalysis has been done on TiO2, which is chemically robust over a wide range of pH. However, TiO2 has a wide band gap (3.2 eV) and can only absorb ∼4% of the solar spectrum, and thus, it will never provide efficient solar energy conversion/storage on its own. Here, we report photocatalytic CO2 reduction with water to produce methanol using TiO2-passivated GaP photocathodes under 532 nm wavelength illumination. The TiO2 layer prevents corrosion of the GaP, as evidenced by atomic force microscopy and photoelectrochemical measurements. Here, the GaP surface is passivated using a thin film of TiO2 deposited by atomic layer deposition (ALD), which provides a viable, stable photocatalyst without sacrificing photocatalytic efficiency. In addition to providing a stable photocatalytic surface, the TiO2 passivation provides substantial enhancement in the photoconversion efficiency through passivation of surface states, which cause nonradiative carrier recombination. In addition to passivation effects, the TiO2 deposited by ALD is n-type due to oxygen vacancies and forms a pn-junction with the underlying p-type GaP photocathode. This creates a built-in field that assists in the separation of photogenerated electron–hole pairs, further reducing recombination. This reduction in the surface recombination velocity (SRV) corresponds to a shift in the overpotential of almost 0.5 V. No enhancement is observed for TiO2 thicknesses above 10 nm, due to the insulating nature of the TiO2, which eventually outweighs the benefits of passivation.

Carbon nanotube (CNT) fibers consist of a network of highly oriented carbon nanotube bundles. This paper explores the ingress of liquids into the contiguous internal pores between the bundles using measurements of contact angles and changes in fiber dimensions. The resultant effects on the internal structure of the fiber have been examined by WAXS and SAXS. A series of time-resolved experiments measured the influence of the structural changes on the electrical resistivity of the fiber. All organic liquids tested rapidly wicked into the fiber to fill its internal void structure. The local regions in which the nanotube bundles are aggregated to give a bundle network were broken up by the liquid ingress. For the range of organic penetrants examined, the strength of the effects on structure and electrical resistivity was correlated, not only with the degree to which the liquid reduced the nanotube surface energy, but also with the Hansen affinity parameters. The fact that liquid environments influence the electrical performance of these fibers is of significance if they are to replace copper as power and signal conductors, with added implications regarding the possible ingress of external insulating materials, and possibly also sensing applications.

Here, we report photocatalytic CO2 reduction with water to produce methanol using TiO2-passivated InP nanopillar photocathodes under 532 nm wavelength illumination. In addition to providing a stable photocatalytic surface, the TiO2-passivation layer provides substantial enhancement in the photoconversion efficiency through the introduction of O vacancies associated with the nonstoichiometric growth of TiO2 by atomic layer deposition. Plane wave-density functional theory (PW-DFT) calculations confirm the role of oxygen vacancies in the TiO2 surface, which serve as catalytically active sites in the CO2 reduction process. PW-DFT shows that CO2 binds stably to these oxygen vacancies and CO2 gains an electron (-0.897e) spontaneously from the TiO2 support. This calculation indicates that the O vacancies provide active sites for CO2 absorption, and no overpotential is required to form the CO2(-) intermediate. The TiO2 film increases the Faraday efficiency of methanol production by 5.7× to 4.79% under an applied potential of -0.6 V vs NHE, which is 1.3 V below the E(o)(CO2/CO2(-)) = -1.9 eV standard redox potential. Copper nanoparticles deposited on the TiO2 act as a cocatalyst and further improve the selectivity and yield of methanol production by up to 8-fold with a Faraday efficiency of 8.7%.

No abstract