The cholesteric liquid crystal self-assembly of water-suspended cellulose nanocrystal (CNC) into a helical arrangement was observed already more than 20 years ago, and the phenomenon was used to produce iridescent solid films by evaporating the solvent or via sol-gel processing. Yet, it remains challenging to produce optically uniform films and to control the pitch reproducibly, reflecting the complexity of the three-stage drying process that is followed in preparing the films. An equilibrium liquid crystal phase formation stage is followed by a non-equilibrium kinetic arrest, which in turn is followed by structural collapse as the remaining solvent is evaporated. Here, we focus on the first of these stages, combining a set of systematic rheology and polarizing optics experiments with computer simulations to establish a detailed phase diagram of aqueous CNC suspensions with two different values of the surface charge, up to the concentration where kinetic arrest sets in. We also study the effect of varying ionic strength of the solvent. Within the cholesteric phase regime, we measure the equilibrium helical pitch as a function of the same parameters. We report a hitherto unnoticed change in character of the isotropic-cholesteric transition at increasing ionic strength, with a continuous weakening of the first-order character up to the point where phase coexistence is difficult to detect macroscopically due to substantial critical fluctuations.

The lyotropic cholesteric liquid crystal phase developed by suspensions of cellulose nanocrystals (CNCs) has come increasingly into focus from numerous directions over the last few years. In part, this is because CNC suspensions are sustainably produced aqueous suspensions of a fully bio-derived nanomaterial with attractive properties. Equally important is the interesting and useful behavior exhibited by solid CNC films, created by drying a cholesteric-forming suspension. However, the pathway along which these films are realized, starting from a CNC suspension that may have low enough concentration to be fully isotropic, is more complex than often appreciated, leading to reproducibility problems and confusion. Addressing a broad audience of physicists, chemists, materials scientists and engineers, this Review focuses primarily on the physics and physical chemistry of CNC suspensions and the process of drying them. The ambition is to explain rather than to repeat, hence we spend more time than usual on the meanings and relevance of the key colloid and liquid crystal science concepts that must be mastered in order to understand the behavior of CNC suspensions, and we present some interesting analyses, arguments and data for the first time. We go through the development of cholesteric nuclei (tactoids) from the isotropic phase and their potential impact on the final dry films; the spontaneous CNC fractionation that takes place in the phase coexistence window; the kinetic arrest that sets in when the CNC mass fraction reaches ∼10 wt.%, preserving the cholesteric helical order until the film has dried; the ’coffee-ring effect’ active prior to kinetic arrest, often ruining the uniformity in the produced films; and the compression of the helix during the final water evaporation, giving rise to visible structural color in the films.

For entropic reasons, the synthesis of macrocycles via olefin ring-closing metathesis (RCM) is impeded by competing acyclic diene metathesis (ADMET) oligomerization. With cationic molybdenum imido alkylidene N-heterocyclic carbene (NHC) complexes confined in tailored ordered mesoporous silica, RCM can be run with macrocyclization selectivities up to 98% and high substrate concentrations up to 0.1 M. Molecular dynamics simulations show that the high conversions are a direct result of the proximity between the surface-bound catalyst, proven by extended X-ray absorption spectroscopy, and the surface-located substrates. Back-diffusion of the macrocycles decreases with decreasing pore diameter of the silica and is responsible for the high macrocyclization efficiency. Also, Z-selectivity increases with decreasing pore diameter and increasing Tolman electronic parameter of the NHC. Running reactions at different concentrations allows for identifying the optimum substrate concentration for each material and substrate combination.

Helical liquid crystal self-assembly in suspensions of cellulose nanocrystals (CNCs), bioderived nanorods exhibiting excellent mechanical and optical properties, opens attractive routes to sustainable production of advanced functional materials. For convenience, in most studies until now, the CNCs were suspended in water, leaving a knowledge gap concerning the influence of the solvent. Using a novel approach for aggregation-free solvent exchange in CNC suspensions, here we show that protic solvents with a high dielectric permittivity εr significantly speed up self-assembly (from days to hours) at high CNC mass fraction and reduce the concentration dependence of the helix period (variation reducing from more than 30 μm to less than 1 μm). Moreover, our computer simulations indicate that the degree of order at constant CNC content increases with increasing εr, leading to a shorter pitch and a reduced threshold for liquid crystallinity. In low-εr solvents, the onset of long-range orientational order is coupled to kinetic arrest, preventing the formation of a helical superstructure. Our results show that the choice of solvent is a powerful parameter for tuning the behavior of CNC suspensions, enhancing our ability to control the self-assembly and thereby harvesting valuable novel cellulose-based materials.

Selectively functionalized mesoporous silica may considerably advance heterogeneous catalysis through the controlled immobilization of highly selective complex catalysts inside the mesopores. However, spatially controlled functionalization and the precise analytical verification are still a challenge. In this publication, we report a method, which ensures a selective functionalization of the mesopore surface with a clickable linker and thus makes it possible to study confinement effects during catalyzed reactions. First, we passivate the silanol groups on the particle surface and in the pore entrances of the mesoporous silica material SBA-15 with 1,1,1-trimethyl-N-(trimethylsilyl) silanamine. Then we remove the template by solvent extraction and functionalize the pore walls with 3-azidopropyltriethoxysilane before we click the catalyst. In initial experiments of asymmetric Rh-catalyzed 1,2-addition, we investigate the performance of a catalyst clicked selectively in the mesopores and compare it to the dissolved catalyst as well as to the catalyst immobilized exclusively on the external surface of SBA-15.