Tissue formation is determined by uncountable biochemical signals between cells; in addition, physical parameters have been shown to exhibit significant effects on the level of the single cell. Beyond the cell, however, there is still no quantitative understanding of how geometry affects tissue growth, which is of much significance for bone healing and tissue engineering. In this paper, it is shown that the local growth rate of tissue formed by osteoblasts is strongly influenced by the geometrical features of channels in an artificial three-dimensional matrix. Curvature-driven effects and mechanical forces within the tissue may explain the growth patterns as demonstrated by numerical simulation and confocal laser scanning microscopy. This implies that cells within the tissue surface are able to sense and react to radii of curvature much larger than the size of the cells themselves. This has important implications towards the understanding of bone remodelling and defect healing as well as towards scaffold design in bone tissue engineering.

Fast actuation speed, large-shape deformation and robust responsiveness are critical to synthetic soft actuators. A simultaneous optimization of all these aspects without trade-offs remains unresolved. Here we describe porous polymer actuators that bend in response to acetone vapour (24 kPa, 20°C) at a speed of an order of magnitude faster than the state-ofthe-art, coupled with a large-scale locomotion. They are meanwhile multi-responsive towards a variety of organic vapours in both the dry and wet states, thus distinctive from the traditional gel actuation systems that become inactive when dried. The actuator is easy-tomake and survives even after hydrothermal processing (200°C, 24 h) and pressing-pressure (100 MPa) treatments. In addition, the beneficial responsiveness is transferable, being able to turn 'inert' objects into actuators through surface coating. This advanced actuator arises from the unique combination of porous morphology, gradient structure and the interaction between solvent molecules and actuator materials.

Most natural materials are composites based on biopolymers and some minerals. Despite the relative paucity of these constituents, their combination yields materials with outstanding properties and a great variation in functionality. A particular characteristic of biological composites is their multifunctionality. The basis for achieving this property is usually a complex hierarchical architecture in which an adaptation to the function(s) is possible at different structural levels. Only a few biological composites have been thoroughly studied from a materials science perspective; nacre is a prominent example. Fueled by the increasing interest in bioinspired materials research, biological composites are now studied more widely, and it has become apparent that Nature often solves materials problems in an unexpected way. This review discusses some striking examples. Many more are likely to emerge in the near future.

We investigated the folding of rectangular stimuli-responsive hydrogel-based polymer bilayers with different aspect ratios and relative thicknesses placed on a substrate. It was found that long-side rolling dominates at high aspect ratios (ratio of length to width) when the width is comparable to the circumference of the formed tubes, which corresponds to a small actuation strain. Rolling from all sides occurs for higher actuation, namely when the width and length considerably exceed the deformed circumference. In the case of moderate actuation, when both the width and length are comparable to the deformed circumference, diagonal rolling is observed. Short-side rolling was observed very rarely and in combination with diagonal rolling. On the basis of experimental observations, finite-element modeling and energetic considerations, we argued that bilayers placed on a substrate start to roll from corners due to quicker diffusion of water. Rolling from the long-side starts later but dominates at high aspect ratios, in agreement with energetic considerations. We have shown experimentally and by modeling that the main reasons causing a variety of rolling scenarios are (i) non-homogenous swelling due to the presence of the substrate and (ii) adhesion of the polymer to the substrate.

Scaffolds for tissue engineering are usually designed to support cell viability with large adhesion surfaces and high permeability to nutrients and oxygen. Recent experiments support the idea that, in addition to surface roughness, elasticity and chemistry, the macroscopic geometry of the substrate also contributes to control the kinetics of tissue deposition. In this study, a previously proposed model for the behavior of osteoblasts on curved surfaces is used to predict the growth of bone matrix tissue in pores of different shapes. These predictions are compared to in vitro experiments with MC3T3-E1 pre-osteoblast cells cultivated in two-millimeter thick hydroxyapatite plates containing prismatic pores with square- or cross-shaped sections. The amount and shape of the tissue formed in the pores measured by phase contrast microscopy confirms the predictions of the model. In cross-shaped pores, the initial overall tissue deposition is twice as fast as in square-shaped pores. These results suggest that the optimization of pore shapes may improve the speed of ingrowth of bone tissue into porous scaffolds.