Bone is a complex highly structured mechanically active 3D tissue composed of cellular and matrix elements. The true biological environment of a bone cell is thus derived from a dynamic interaction between responsively active cells experiencing mechanical forces and a continuously changing 3D matrix architecture. To investigate this phenomenon in vitro, marrow stromal osteoblasts were cultured on 3D scaffolds under flow perfusion with different rates of flow for an extended period to permit osteoblast differentiation and significant matrix production and mineralization. With all flow conditions, mineralized matrix production was dramatically increased over statically cultured constructs with the total calcium content of the cultured scaffolds increasing with increasing flow rate. Flow perfusion induced de novo tissue modeling with the formation of pore-like structures in the scaffolds and enhanced the distribution of cells and matrix throughout the scaffolds. These results represent reporting of the long-term effects of fluid flow on primary differentiating osteoblasts and indicate that fluid flow has far-reaching effects on osteoblast differentiation and phenotypic expression in vitro. Flow perfusion culture permits the generation and study of a 3D, actively modeled, mineralized matrix and can therefore be a valuable tool for both bone biology and tissue engineering. Bone is a complex, highly organized tissue consisting of a structured extracellular matrix composed of inorganic and organic elements containing a conglomeration of cell types responsible for its metabolism and upkeep that are responsive to a variety of signals (1). As would be expected from the skeleton's central role in support and structural integrity, bone cells cultured in vitro respond to a variety of different mechanical signals including fluid flow, hydrostatic pressure, and substrate deformation.Current studies indicate that fluid flow is a potentially stronger stimulus for bone cell behavior than either hydrostatic compression (2) or substrate deformation (3, 4). The in vitro mechanical stimulation of bone cells by fluid flow has been reported to impact the levels of many biochemical factors including intracellular calcium (5, 6), nitric oxide (4, 7-9), prostaglandin E 2 (3, 4, 7, 8), the expression of the genes for osteopontin, cyclooxygenase-2, and c-Fos (6, 10-12) as well as other intracellular messengers and transcription factors (6,(13)(14)(15). This mechanostimulation of bone cells in vitro by fluid flow mimics the physiological response of bone cells in vivo where pressure gradients from mechanical loading of locomotion and other stressors deform the mineralized bone matrix and move extracellular fluid radially outward toward the cortex through the lacunocanalicular network (16)(17)(18)(19). Mechanical loading of bone plays an important role because it can both increase bone formation and decrease bone resorption (1). Indeed, its absence can lead to lower bone matrix protein production, mineral content, and bone formation plus incr...

The objective of this study was to evaluate the effect of two cell culture techniques, static and flow perfusion, on the osteogenic expression of rat bone marrow cells seeded into titanium fiber mesh for a period up to 16 days. A cell suspension of rat bone marrow stromal osteoblasts (5 x 10(5) cells/300 microL) was seeded into the mesh material. Thereafter, the constructs were cultured under static conditions or in a flow perfusion system for 4, 8, and 16 days. To evaluate cellular proliferation and differentiation, constructs were examined for DNA, calcium content, and alkaline phosphatase activity. Samples were also examined with scanning electron microscopy (SEM) and plastic-embedded histological sections. Results showed an increase in DNA from day 4 to day 8 for the flow perfusion system. At day 8, a significant enhancement in DNA content was observed for flow perfusion culture compared with static culture conditions, but similar cell numbers were found for each culture system at 16 days. Calcium measurements showed a large increase in calcium content of the meshes subjected to flow perfusion at day 16. The SEM examination revealed that the 16-day samples subjected to flow perfusion culture were completely covered with layers of cells and mineralized matrix. In addition, this matrix extended deep into the scaffolds. In contrast, meshes cultured under static conditions had only a thin sheet of matrix present on the upper surface of the meshes. Evaluation of the light microscopy sections confirmed the SEM observations. On the basis of our results, we conclude that a flow perfusion system can enhance the early proliferation, differentiation, and mineralized matrix production of bone marrow stromal osteoblasts seeded in titanium fiber mesh.

The objective of this study was to investigate if the in vitro pre-culture period in osteogenic media of rat mesenchymal stem cells (MSCs), influences their ability to regenerate bone when implanted in a critical size cranial defect. MSCs were harvested from the bone marrow of 6-8 weeks old male Fisher rats and expanded in vitro in osteogenic media for different time periods (4, 10, and 16 days) in tissue culture plates (TCP), seeded on sintered titanium fiber meshes without the extracellular matrix (ECM) generated in vitro, and implanted in the rat cranium after 12 h. Thirty two adult Fisher rats received the implants, divided in four groups. Three groups were implanted with cells cultured for 4, 10, or 16 days in osteogenic media and at that time their alkaline phosphatase activity and mineral deposition denoted that they were at different stages of their osteoblastic maturation (undifferentiated MSC, committed, and mature Osteoblasts, respectively). MSCs cultured without osteogenic media for 6 days were used as controls. The constructs were retrieved 4 weeks later and processed for histomorphometric analysis. Implants seeded with cells that have been cultured with osteogenic media for only 4 days revealed the highest bone formation. The lowest bone formation was obtained with the implants seeded with MSCs cultured for 16 days in the presence of osteogenic media. The results of this study suggested that the in vitro pre-culture period of MSCs is a critical factor for their ability to regenerate bone when implanted to an orthotopic site.

In this study, the mechanical properties of an implanted calcium phosphate (CaP) cement incorporated with 20wt% poly (dl-lactic-co-glycolic acid) (PLGA) microparticles were investigated in a rat cranial defect. After 2, 4 and 8 weeks of implantation, implants were evaluated mechanically (push-out test) and morphologically (Scanning Electron Microscopy (SEM) and histology). The results of the push-out test showed that after 2 weeks the shear strength of the implants was 0.44+/-0.44MPa (average+/-sd), which increased to 1.34+/-1.05MPa at 4 weeks and finally resulted in 2.60+/-2.78MPa at 8 weeks. SEM examination showed a fracture plane at the bone-cement interface at 2 weeks, while the 4- and 8-week specimens created a fracture plane into the CaP/PLGA composites, indicating an increased strength of the bone-cement interface. Histological evaluation revealed that the two weeks implantation period resulted in minimal bone ingrowth, while at 4 weeks of implantation the peripheral PLGA microparticles were degraded and replaced by deposition of newly formed bone. Finally, after 8 weeks of implantation the degradation of the PLGA microparticles was almost completed, which was observed by the bone ingrowth throughout the CaP/PLGA composites. On basis of our results, we conclude that the shear strength of the bone-cement interface increased over time due to bone ingrowth into the CaP/PLGA composites. Although the bone-cement contact could be optimized with an injectable CaP cement to enhance bone ingrowth, still the mechanical properties of the composites after 8 weeks of implantation are insufficient for load-bearing purposes.