Bioinspired manufacturing, in the sense of replicating the way nature fabricates, may hold great potential for supporting a socioeconomic transformation towards a sustainable society. Use of unmodified ubiquitous biological components suggests for a fundamentally sustainable manufacturing paradigm where materials are produced, transformed into products and degraded in closed regional systems with limited requirements for transport. However, adoption is currently limited by the fact that despite their ubiquitous nature, these biopolymers are predominantly harvested as industrial and agricultural products. in this study, we overcome this limitation by developing a link between bioinspired manufacturing and urban waste bioconversion. this result is paramount for the development of circular economic models, effectively connecting the organic by-products of civilization to locally decentralized, general-purpose manufacturing.are placed together (Fig. 4b); from the 0.5 mm post-drying layer definition of the insect replica to the 5 m height of the original crustacean-plant version, there are four orders of magnitude achieved using the same free-form manufacturing system and material. Scientific RepoRtS |(2020) 10:4632 | https://doi.Where, [η] is intrinsic viscosity, K and α are Mark-Houwink Constants. The values of K and α are taken from what was previously determined with identical setting as 0.74 ×10 −3 and 0.76, respectively.Mechanical testing. The mechanical properties of chitosan film and FLAM of insect chitin were evaluated by the tensile test performed using UTM (Universal Testing Machine-Instron 5943) equipped with 1 kN load cell with a cross head speed of 4 mm min −1 at ambient conditions according to the standard method (ASTM D1037-12) 15 . Chitosan films specimens were cut into strips with 70 mm length and 20 mm width. Thickness of the chitosan film were measured by SEM. The specimens for FLAMs were cast in a dog-bone shape mold with 100 × 16 × 6 mm size in the reduced section and allowed to dry in an oven at 50 °C for 24 h before test. 3-point bending test: FLAM (CC 1:8) were tested for the flexural test following ASTM standards (D1037-12) on UTM equipped with 3-point flexure test fixtures. A support span of 60 mm and head speed of 4 mm min −1 was used.figures. Figures and clip art compositions were prepared using Adobe Illustrator (Adobe Inc, San Jose, California, U.S.). Photographs were taken using a Canon EOS 50D camera (Canon Inc. Ota City, Tokyo, Japan) with 18-55 mm lens.

Thermal stress drives the bleaching of reef corals, during which the endosymbiotic relationship between Symbiodiniaceae microalgae and the host breaks down. The endosymbiont communities are known to shift in response to environmental disturbances, but how they respond within and between colonies during and following bleaching events remains unclear. In 2016, a major global-scale bleaching event hit countless tropical reefs. Here, we investigate the relative abundances of Cladocopium LaJeunesse & H.J.Jeong, 2018 and Durusdinium LaJeunesse, 2018 within and among Pachyseris speciosa colonies in equatorial Singapore that are known to host both these Symbiodiniaceae clades. Bleached and unbleached tissues from bleaching colonies, as well as healthy colonies, during and following the bleaching event were sampled and analyzed for comparison. The nuclear ribosomal internal transcribed spacer (ITS) regions were separately amplified and quantified using a SYBR Green-based quantitative polymerase chain reaction (qPCR) method and Illumina high-throughput sequencing. We found Cladocopium to be highly abundant relative to Durusdinium. The relative abundance of Durusdinium, known to be thermally tolerant, was highest in post-bleaching healthy colonies, while bleached and unbleached tissues from bleaching colonies as well as tissue from healthy colonies during the event had depressed proportions of Durusdinium. Given the importance of Durusdinium for thermal tolerance and stress response, it is surprising that bleached tissue showed limited change over healthy tissue during the bleaching event. Moreover, colonies were invariably dominated by Cladocopium during bleaching, but a minority of colonies were Durusdinium-dominant during non-bleaching times. The detailed characterization of Symbiodiniaceae in specific colonies during stress and recovery will provide insights into this crucial symbiosis, with implications for their responses during major bleaching events.

An optimized extraction protocol for eumelanins from black soldier flies (BSF-Eumel) allows an in-depth study of natural eumelanin pigments, which are a valuable tool for the design and fabrication of sustainable scaffolds. Here, water-soluble BSF-Eumel sub-micrometer colloidal particles were used as bioactive signals for developing a composite biomaterial ink for scaffold preparation. For this purpose, BSF-Eumel was characterized both chemically and morphologically; moreover, biological studies were carried out to investigate the dose-dependent cell viability and its influence on human mesenchymal stem cells (hMSCs), with the aim of validating suitable protocols and to find an optimal working concentration for eumelanin-based scaffold preparation. As proof of concept, 3D printed scaffolds based on methacrylated hyaluronic acid (MEHA) and BSF-Eumel were successfully produced. The scaffolds with and without BSF-Eumel were characterized in terms of their physico-chemical, mechanical and biological behaviours. The results showed that MEHA/BSF-Eumel scaffolds had similar storage modulus values to MEHA scaffolds. In terms of swelling ratio and stability, these scaffolds were able to retain their structure without significant changes over 21 days. Biological investigations demonstrated the ability of the bioactivated scaffolds to support the adhesion, proliferation and osteogenic differentiation of human mesenchymal stem cells.

Gellan gum (GG) was chemically modified with methacrylic moieties to produce a photocrosslinkable biomaterial ink, hereinafter called methacrylated GG (GGMA), with improved physico-chemical properties, mechanical behavior and stability under physiological conditions. Afterwards, GGMA was functionalized by incorporating two different bioactive compounds, a naturally derived eumelanin extracted from the black soldier fly (BSF-Eumel), or hydroxyapatite nanoparticles (HAp), synthesized by the sol–gel method. Different ink formulations based on GGMA (2 and 4% (w/v)), BSF-Eumel, at a selected concentration (0.3125 mg/mL), or HAp (10 and 30% wHAp/wGGMA) were developed and processed by three-dimensional (3D) printing. All the functionalized GGMA-based ink formulations allowed obtaining 3D-printed GGMA-based scaffolds with a well-organized structure. For both bioactive signals, the scaffolds with the highest GGMA concentration (4% (w/v)) and the highest percentage of infill (45%) showed the best performances in terms of morphological and mechanical properties. Indeed, these scaffolds showed a good structural integrity over 28 days. Given the presence of negatively charged groups along the eumelanin backbone, scaffolds consisting of GGMA/BSF-Eumel demonstrated a higher stability. From a mechanical point of view, GGMA/BSF-Eumel scaffolds exhibited values of storage modulus similar to those of GGMA ones, while the inclusion of HAp at 30% (wHAp/wGGMA) led to a storage modulus of 32.5 kPa, 3.5-fold greater than neat GGMA. In vitro studies proved the capability of the bioactivated 3D-printed scaffolds to support 7F2 osteoblast cell growth and differentiation. BSF-Eumel and HAp triggered a different time-dependent physiological response in the osteoblasts. Specifically, while the ink with BSF-Eumel acted as a stimulus towards cell proliferation, reaching the highest value at 14 days, a higher expression of alkaline phosphatase activity was detected for scaffolds consisting of GGMA and HAp. The overall findings demonstrated the possible use of these biomaterial inks for 3D-printed bone tissue-engineered scaffolds.