The nucleation of graphene on a transition metal surface, either on a terrace or near a step edge, is systematically explored using density functional theory calculations and applying the two-dimensional (2D) crystal nucleation theory. Careful optimization of the supported carbon clusters, C(N) (with size N ranging from 1 to 24), on the Ni(111) surface indicates a ground state structure transformation from a one-dimensional C chain to a 2D sp(2) C network at N ≈ 10-12. Furthermore, the crucial parameters controlling graphene growth on the metal surface, nucleation barrier, nucleus size, and nucleation rate on a terrace or near a step edge are calculated. In agreement with numerous experimental observations, our analysis shows that graphene nucleation near a metal step edge is superior to that on a terrace. On the basis of our analysis, we propose the use of graphene seeds to synthesize high-quality graphene in large area.

Rational design of single atom catalyst is critical for efficient sustainable energy conversion. However, the atomic-level control of active sites is essential for electrocatalytic materials in alkaline electrolyte. Moreover, well-defined surface structures lead to in-depth understanding of catalytic mechanisms. Herein, we report a single-atomic-site ruthenium stabilized on defective nickel-iron layered double hydroxide nanosheets (Ru1/D-NiFe LDH). Under precise regulation of local coordination environments of catalytically active sites and the existence of the defects, Ru1/D-NiFe LDH delivers an ultralow overpotential of 18 mV at 10 mA cm−2 for hydrogen evolution reaction, surpassing the commercial Pt/C catalyst. Density functional theory calculations reveal that Ru1/D-NiFe LDH optimizes the adsorption energies of intermediates for hydrogen evolution reaction and promotes the O–O coupling at a Ru–O active site for oxygen evolution reaction. The Ru1/D-NiFe LDH as an ideal model reveals superior water splitting performance with potential for the development of promising water-alkali electrocatalysts.

Rational design of the catalysts is impressive for sustainable energy conversion. However, there is a grand challenge to engineer active sites at the interface. Herein, hierarchical transition bimetal oxides/sulfides heterostructure arrays interacting two-dimensional MoOx/MoS2 nanosheets attached to one-dimensional NiOx/Ni3S2 nanorods were fabricated by oxidation/hydrogenation-induced surface reconfiguration strategy. The NiMoOx/NiMoS heterostructure array exhibits the overpotentials of 38 mV for hydrogen evolution and 186 mV for oxygen evolution at 10 mA cm−2, even surviving at a large current density of 500 mA cm−2 with long-term stability. Due to optimized adsorption energies and accelerated water splitting kinetics by theory calculations, the assembled two-electrode cell delivers the industrially relevant current densities of 500 and 1000 mA cm−2 at record low cell voltages of 1.60 and 1.66 V with excellent durability. This research provides a promising avenue to enhance the electrocatalytic performance of the catalysts by engineering interfacial active sites toward large-scale water splitting.

In the fabrication and processing of silicene monolayers, structural defects are almost inevitable. Using ab initio calculations, we systemically investigated the structures, formation energies, migration behaviors and electronic/magnetic properties of typical point defects in silicene, including the Stone-Wales (SW) defect, single and double vacancies (SVs and DVs), and adatoms. We found that SW can be effectively recovered by thermal annealing. SVs have much higher mobility than DVs and two SVs are very likely to coalesce into one DV to lower the energy. Existence of SW and DVs may induce small gaps in silicene, while the SV defect may transform semimetallic silicene into metallic. Adatoms are unexpectedly stable and can affect the electronic properties of silicene dramatically. Especially, Si adatoms as self-dopants in silicene sheets can induce long-range spin polarization as well as a remarkable band gap, thus achieving an all-silicon magnetic semiconductor. The present theoretical results provide valuable insights into identification of these defects in experiments and understanding their effects on the physical properties of silicene.