Antifouling membranes that offer excellent operational lifetimes are critical technologies needed to meet the growing demand for clean water. In this study, we demonstrate antifouling membranes featuring an ultrathin oil layer that stayed immobilized on the surface and in the pore walls of poly­(vinylidene fluoride) membranes for multiple cycles of operation at industrially relevant transmembrane pressures. An optimized quantity of a commercial Krytox oil with either a low (K103) or a high viscosity (K107) was infused onto the active surface and into the pores of membranes with a 0.45 μm pore size. The presence of the oil layer was qualitatively confirmed using crystal violet staining and variable pressure scanning electron microscopy. Using a dead-end stirred cell, a consistent pure water permeance value of 3000 L m–2 h–1 bar–1 was achieved for the K103 liquid-infused membranes for at least 10 operation cycles, which was expectedly lower than the permeance of bare control membranes (∼16 000 L m–2 h–1 bar–1), suggesting that a stable oil layer was formed on all membrane-active sites. To quantify if oil was lost during membrane operation, extensive thermogravimetric analysis was conducted on both the as-prepared and used membranes. When challenged with the microorganism, Escherichia coli K12, the liquid-infused membranes statistically reduced microbial attachment by ∼50% versus the control membranes. For the first time, we have demonstrated that by forming an immobilized, robust, and stable oil-coated membrane, we can generate high-performance membranes with stable permeance values that can be operated at relevant transmembrane pressures and provide long-lasting antifouling properties.

The COVID-19 pandemic has revealed the importance of the detection of airborne pathogens. Here, we present composite air filters featuring a bioinspired liquid coating that facilitates the removal of captured aerosolized bacteria and viruses for further analysis. We tested three types of air filters: commercial polytetrafluoroethylene (PTFE), which is well known for creating stable liquid coatings, commercial high-efficiency particulate air (HEPA) filters, which are widely used, and in-house-manufactured cellulose nanofiber mats (CNFMs), which are made from sustainable materials. All filters were coated with omniphobic fluorinated liquid to maximize the release of pathogens. We found that coating both the PTFE and HEPA filters with liquid improved the rate at which Escherichia coli was recovered using a physical removal process compared to uncoated controls. Notably, the coated HEPA filters also increased the total number of recovered cells by 57%. Coating the CNFM filters did not improve either the rate of release or the total number of captured cells. The most promising materials, the liquid-coated HEPA, filters were then evaluated for their ability to facilitate the removal of pathogenic viruses via a chemical removal process. Recovery of infectious JC polyomavirus, a nonenveloped virus that attacks the central nervous system, was increased by 92% over uncoated controls; however, there was no significant difference in the total amount of genomic material recovered compared to that of controls. In contrast, significantly more genomic material was recovered for SARS-CoV-2, the airborne, enveloped virus, which causes COVID-19, from liquid-coated filters. Although the amount of infectious SARS-CoV-2 recovered was 58% higher, these results were not significantly different from uncoated filters due to high variability. These results suggest that the efficient recovery of airborne pathogens from liquid-coated filters could improve air sampling efforts, enhancing biosurveillance and global pathogen early warning.

The COVID-19 pandemic has revealed the importance of the detection of airborne pathogens. Here, we present composite air filters featuring a bio-inspired liquid coating that facilitates the removal of captured aerosolized bacteria and viruses for further analysis. We tested three types of air filters: commercial polytetrafluoroethylene (PTFE), which is well-known for creating stable liquid coatings, commercial high-efficiency particulate air (HEPA) filters, which are widely used, and in-house manufactured cellulose nanofiber mats (CNFM), which are made from sustainable materials. All filters were coated with omniphobic fluorinated liquid to maximize release. We found that coating both the PTFE and HEPA filters with liquid improved the rate at which Escherichia coli was recovered using a physical removal process compared to uncoated controls. Notably, the coated HEPA filters also increased the total number of recovered cells by 57%. Coating the CNFM filters did not improve either the rate of release or total number of captured cells. The ability of the highest performance materials, the liquid-coated HEPA filters were next evaluated on their ability to facilitate the removal of pathogenic viruses via a chemical removal process. Recovery of infectious JC polyomavirus, a non-enveloped virus which attacks the central nervous system, was increased by 92% over uncoated controls; however, there was no significant difference in the total amount of RNA recovered compared to controls. In contrast, significantly more RNA was recovered for SARS-CoV-2, the airborne, enveloped virus which causes COVID-19, from liquid-coated filters. Although the amount of infectious SARS-CoV-2 recovered was 58% higher, these results were not significantly different from uncoated filters due to high variability. These results suggest that the efficient recovery of airborne pathogens from filters could improve air sampling efforts, enhancing biosurveillance and global pathogen early warning.