While turbine rim sealing flows are an important aspect of turbomachinery design, affecting turbine aerodynamic performance and turbine disk temperatures, the present understanding and predictive capability for such flows is limited. The aim of the present study is to clarify the flow physics involved in rim sealing flows and to provide high-quality experimental data for use in evaluation of computational fluid dynamics (CFD) models. The seal considered is similar to a chute seal previously investigated by other workers, and the study focuses on the inherent unsteadiness of rim seal flows, rather than unsteadiness imposed by the rotating blades. Unsteady pressure measurements from radially and circumferentially distributed transducers are presented for flow in a rotor–stator disk cavity and the rim seal without imposed external flow. The test matrix covered ranges in rotational Reynolds number, Re∅, and nondimensional flow rate, Cw, of 2.2–3.0 × 106 and 0–3.5 × 103, respectively. Distinct frequencies are identified in the cavity flow, and detailed analysis of the pressure data associates these with large-scale flow structures rotating about the axis. This confirms the occurrence of such structures as predicted in previously published CFD studies and provides new data for detailed assessment of CFD models.
Pronounced nonuniformities in combustor exit flow temperature (hot-streaks), which arise because of discrete injection of fuel and dilution air jets within the combustor and because of endwall cooling flows, affect both component life and aerodynamics. Because it is very difficult to quantitatively predict the effects of these temperature nonuniformities on the heat transfer rates, designers are forced to budget for hot-streaks in the cooling system design process. Consequently, components are designed for higher working temperatures than the mass-mean gas temperature, and this imposes a significant overall performance penalty. An inadequate cooling budget can lead to reduced component life. An improved understanding of hot-streak migration physics, or robust correlations based on reliable experimental data, would help designers minimize the overhead on cooling flow that is currently a necessity. A number of recent research projects sponsored by a range of industrial gas turbine and aero-engine manufacturers attest to the growing interest in hot-streak physics. This paper presents measurements of surface and endwall heat transfer rate for a high-pressure (HP) nozzle guide vane (NGV) operating as part of a full HP turbine stage in an annular transonic rotating turbine facility. Measurements were conducted with both uniform stage inlet temperature and with two nonuniform temperature profiles. The temperature profiles were nondimensionally similar to profiles measured in an engine. A difference of one-half of an NGV pitch in the circumferential (clocking) position of the hot-streak with respect to the NGV was used to investigate the affect of clocking on the vane surface and endwall heat transfer rate. The vane surface pressure distributions, and the results of a flow-visualization study, which are also given, are used to aid interpretation of the results. The results are compared to two-dimensional predictions conducted using two different boundary layer methods. Experiments were conducted in the Isentropic Light Piston Facility (ILPF) at QinetiQ Farnborough, a short-duration engine-sized turbine facility. Mach number, Reynolds number, and gas-to-wall temperature ratios were correctly modeled. It is believed that the heat transfer measurements presented in this paper are the first of their kind.
This paper details the improvements made to the design and fabrication of thin-film heat flux gauges at Oxford. These improvements have been driven by the desire to improve measurement accuracy and resolution in short duration wind-tunnel experiments. A thin-film heat flux gauge (TFHFG) measures heat flux by recording the temperature history of thin film resistive temperature sensors sputtered onto an insulating substrate. The heat flux can then be calculated using Fourier’s law of heat conduction. A new fabrication process utilising technology from the manufacture of flexible printed circuit boards is outlined, which enables the production of significantly smaller and more robust gauges than those previously used.
This paper presents an investigation of the aerothermal performance of a modern unshrouded high-pressure (HP) aero-engine turbine subject to nonuniform inlet temperature profile. The turbine used for this study was the MT1 turbine installed in the QinetiQ turbine test facility based in Farnborough (UK). The MT1 turbine is a full scale transonic HP turbine, and is operated in the test facility at the correct nondimensional conditions for aerodynamics and heat transfer. Datum experiments of aerothermal performance were conducted with uniform inlet conditions. Experiments with nonuniform inlet temperature were conducted with a temperature profile that had a nonuniformity in the radial direction defined by (Tmax−Tmin)/T¯=0.355, and a nonuniformity in the circumferential direction defined by (Tmax−Tmin)/T¯=0.14. This corresponds to an extreme point in the engine cycle, in an engine where the nonuniformity is dominated by the radial distribution. Accurate experimental area surveys of the turbine inlet and exit flows were conducted, and detailed heat transfer measurements were obtained on the blade surfaces and end-walls. These results are analyzed with the unsteady numerical data obtained using the in-house HybFlow code developed at the University of Firenze. Two particular aspects are highlighted in the discussion: prediction confidence for state of the art computational fluid dynamics (CFD) and impact of real conditions on stator-rotor thermal loading. The efficiency value obtained with the numerical analysis is compared with the experimental data and a 0.8% difference is found and discussed. A study of the flow field influence on the blade thermal load has also been detailed. It is shown that the hot streak migration mainly affects the rotor pressure side from 20% to 70% of the span, where the Nusselt number increases by a factor of 60% with respect to the uniform case. Furthermore, in this work, it has been found that a nonuniform temperature distribution is beneficial for the rotor tip, contrary to the results found in open literature. Although the hot streak is affected by the pressure gradient across the tip gap, the radial profile (which dominates the temperature profile being considered) is not fully mixed out in passing through the HP stage, and contributes significantly to cooling the turbine casing. A design approach not taking into account these effects will underestimate the rotor life near the tip and the thermal load at midspan. The temperature profile that has been used in both experiments and CFD is the first simulation of an extreme cycle point (more than twice the magnitude of distortion of all previous experimental studies): It represents an engine-take-off condition combined with the full combustor cooling. This research was part of the EU funded Turbine AeroThermal External Flows 2 program.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.