HT-ATES (high-temperature aquifer thermal energy storage) systems are a future option to shift large amounts of high-temperature excess heat from summer to winter using the deep underground. Among others, water-bearing reservoirs in former hydrocarbon formations show favorable storage conditions for HT-ATES locations. This study characterizes these reservoirs in the Upper Rhine Graben (URG) and quantifies their heat storage potential numerically. Assuming a doublet system with seasonal injection and production cycles, injection at 140 °C in a typical 70 °C reservoir leads to an annual storage capacity of up to 12 GWh and significant recovery efficiencies increasing up to 82% after ten years of operation. Our numerical modeling-based sensitivity analysis of operational conditions identifies the specific underground conditions as well as drilling configuration (horizontal/vertical) as the most influencing parameters. With about 90% of the investigated reservoirs in the URG transferable into HT-ATES, our analyses reveal a large storage potential of these well-explored oil fields. In summary, it points to a total storage capacity in depleted oil reservoirs of approximately 10 TWh a−1, which is a considerable portion of the thermal energy needs in this area.

<p>In central Europe, the majority of the CO<sub>2</sub> emissions in the energy sector are related to the provision of building and process heat. Due to seasonal fluctuations in demand, especially to provide heat for residential and industrial buildings, local storage of excess heat in summer for utilization in winter is becoming increasingly important. With the current state of technology and foreseeable developments, sufficient amounts of heat can only be stored underground, taking advantage of the large available storage volumes. In contrast to typical near-surface aquifer thermal energy storage (ATES), the utilization of deep reservoirs enables the storage of much larger thermal energies due to potentially significantly higher injection temperatures (e.g. > 80 °C).</p> <p>Previous studies demonstrated the high potential of deep reservoirs for high-temperature (HT) ATES, in particular for former hydrocarbon reservoirs in the Upper Rhine Graben. However, these studies focused on thermo-hydraulic processes, only rarely considering the impact of coupled mechanical processes. Using the case study of the DeepStor project, a demonstrator for HT-ATES under development in the north of Karlsruhe (Germany), the present study investigates the influence of coupled thermo-hydraulic-mechanical (THM) processes during the operation of HT-ATES systems.</p> <p>In particular, we investigate the impact of seasonal HT-ATES with biannual injection/production cycles on the stress distribution in the subsurface and subsequently caused displacements in the reservoir and the surface as well as the shear capacity at faults. This study further aims at improving the understanding of poro- and thermoelastic processes related to HT-ATES. Whereas the thermoelastic component dominates the vertical displacements at the top of the reservoir, the uplift at the surface is primarily controlled by the poroelastic component. Furthermore, an assessment of potential risks such as surface uplift or shear capacity at faults is performed. Our results show that surface uplift is primarily controlled by the reservoir depth, Young’s modulus, and the injection/production flow rate.</p>

Abstract. Motivated by the unknown reasons for a kilometre-scale high-temperature overprint of 270–300 ∘C in a reservoir outcrop analogue (Piesberg quarry, northwestern Germany), numerical simulations are conducted to identify the transport mechanisms of the fault-related hydrothermal convection system. The system mainly consists of a main fault and a sandstone reservoir in which transfer faults are embedded. The results show that the buoyancy-driven convection in the main fault is the basic requirement for elevated temperatures in the reservoir. We studied the effects of permeability variations and lateral regional flow (LRF) mimicking the topographical conditions on the preferential fluid-flow pathways, dominant heat-transfer types, and mutual interactions among different convective and advective flow modes. The sensitivity analysis of permeability variations indicates that lateral convection in the sandstone and advection in the transfer faults can efficiently transport fluid and heat, thus causing elevated temperatures (≥269 ∘C) in the reservoir at a depth of 4.4 km compared to purely conduction-dominated heat transfer (≤250 ∘C). Higher-level lateral regional flow interacts with convection and advection and changes the dominant heat transfer from conduction to advection in the transfer faults for the low permeability cases of sandstone and main fault. Simulations with anisotropic permeabilities detailed the dependence of the onset of convection and advection in the reservoir on the spatial permeability distribution. The depth-dependent permeabilities of the main fault reduce the amount of energy transferred by buoyancy-driven convection. The increased heat and fluid flows resulting from the anisotropic main fault permeability provide the most realistic explanation for the thermal anomalies in the reservoir. Our numerical models can facilitate exploration and exploitation workflows to develop positive thermal anomaly zones as geothermal reservoirs. These preliminary results will stimulate further petroleum and geothermal studies of fully coupled thermo–hydro–mechanical–chemical processes in faulted tight sandstones.

No abstract

No abstract