We report on the microstructure and dynamics of electron transport and recombination in dye-sensitized solar cells (DSSCs) incorporating oriented TiO2 nanotube (NT) arrays. The morphology of the NT arrays, which were prepared from electrochemically anodized Ti foils, were characterized by scanning and transmission electron microscopies. The arrays were found to consist of closely packed NTs, several micrometers in length, with typical wall thicknesses and intertube spacings of 8-10 nm and pore diameters of about 30 nm. The calcined material was fully crystalline with individual NTs consisting of about 30 nm sized crystallites. The transport and recombination properties of the NT and nanoparticle (NP) films used in DSSCs were studied by frequency-resolved modulated photocurrent/photovoltage spectroscopies. While both morphologies display comparable transport times, recombination was much slower in the NT films, indicating that the NT-based DSSCs have significantly higher charge-collection efficiencies than their NP-based counterparts. Dye molecules were shown to cover both the interior and exterior walls of the NTs. Analysis of photocurrent measurements indicates that the light-harvesting efficiencies of NT-based DSSCs were higher than those found for DSSCs incorporating NPs owing to stronger internal light-scattering effects.

Goldschmidt tolerance factor (t) is an empirical index for predicting stable crystal structures of perovskite materials. A t value between 0.8 and 1.0 is favorable for cubic perovskite structure, and larger (>1) or smaller (<0.8) values of tolerance factor usually result in nonperovskite structures. CH­(NH2)2PbI3 (FAPbI3) can exist in the perovskite α-phase (black phase) with good photovoltaic properties. However, it has a large tolerance factor and is more stable in the hexagonal δH-phase (yellow phase), with δH-to-α phase-transition temperature higher than room temperature. On the other hand, CsPbI3 is stabilized to an orthorhombic structure (δO-phase) at room temperature due to its small tolerance factor. We find that, by alloying FAPbI3 with CsPbI3, the effective tolerance factor can be tuned, and the stability of the photoactive α-phase of the mixed solid-state perovskite alloys FA1–x Cs x PbI3 is enhanced, which is in agreement with our first-principles calculations. Thin films of the FA0.85Cs0.15PbI3 perovskite alloy demonstrate much improved stability in a high-humidity environment; this contrasts significantly with the pure FAPbI3 film for which the α-to-δH phase transition (associated with yellowing appearance) is accelerated by humidity environment. Due to phase stabilization, the FA0.85Cs0.15PbI3 solid-state alloy showed better solar cell performance and device stability than its FAPbI3 counterparts. Our studies suggest that tuning the tolerance factor through solid-state alloying can be a general strategy to stabilize the desired perovskite structure for solar cell applications.

No abstract

Organic and inorganic hybrid perovskites (e.g., CH(3)NH(3)PbI(3)), with advantages of facile processing, tunable bandgaps, and superior charge-transfer properties, have emerged as a new class of revolutionary optoelectronic semiconductors promising for various applications. Perovskite solar cells constructed with a variety of configurations have demonstrated unprecedented progress in efficiency, reaching about 20% from multiple groups after only several years of active research. A key to this success is the development of various solution-synthesis and film-deposition techniques for controlling the morphology and composition of hybrid perovskites. The rapid progress in material synthesis and device fabrication has also promoted the development of other optoelectronic applications including light-emitting diodes, photodetectors, and transistors. Both experimental and theoretical investigations on organic-inorganic hybrid perovskites have enabled some critical fundamental understandings of this material system. Recent studies have also demonstrated progress in addressing the potential stability issue, which has been identified as a main challenge for future research on halide perovskites. Here, we review recent progress on hybrid perovskites including basic chemical and crystal structures, chemical synthesis of bulk/nanocrystals and thin films with their chemical and physical properties, device configurations, operation principles for various optoelectronic applications (with a focus on solar cells), and photophysics of charge-carrier dynamics. We also discuss the importance of further understanding of the fundamental properties of hybrid perovskites, especially those related to chemical and structural stabilities.