This study presents a novel, green, and efficient way of preparing crosslinked aerogels from cellulose nanofibers (CNFs) and alginate using non‐covalent chemistry. This new process can ultimately facilitate the fast, continuous, and large‐scale production of porous, light‐weight materials as it does not require freeze‐drying, supercritical CO2 drying, or any environmentally harmful crosslinking chemistries. The reported preparation procedure relies solely on the successive freezing, solvent‐exchange, and ambient drying of composite CNF‐alginate gels. The presented findings suggest that a highly‐porous structure can be preserved throughout the process by simply controlling the ionic strength of the gel. Aerogels with tunable densities (23–38 kg m−3) and compressive moduli (97–275 kPa) can be prepared by using different CNF concentrations. These low‐density networks have a unique combination of formability (using molding or 3D‐printing) and wet‐stability (when ion exchanged to calcium ions). To demonstrate their use in advanced wet applications, the printed aerogels are functionalized with very high loadings of conducting poly(3,4‐ethylenedioxythiophene):tosylate (PEDOT:TOS) polymer by using a novel in situ polymerization approach. In‐depth material characterization reveals that these aerogels have the potential to be used in not only energy storage applications (specific capacitance of 78 F g−1), but also as mechanical‐strain and humidity sensors.

The macro- and microstructural evolution of water swollen and ethanol swollen regenerated cellulose gel beads have been determined during drying by optical microscopy combined with analytical balance measurements, small-angle X-ray scattering (SAXS), and wide-angle X-ray scattering (WAXS). Two characteristic length scales, which are related to the molecular dimension of cellulose monomer and elongated aggregates of these monomers, could be identified for both types of beads by SAXS. For ethanol swollen beads, only small changes to the structures were detected in both the SAXS and WAXS measurements during the entire drying process. However, the drying of cellulose from water follows a more complex process when compared to drying from ethanol. As water swollen beads dried, they went through a structural transition where elongated structures changed to spherical structures and their dimensions increased from 3.6 to 13.5 nm. After complete drying from water, the nanostructures were characterized as a combination of rodlike structures with an approximate size of cellulose monomers (0.5 nm), and spherical aggregates (13.5 nm) without any indication of heterogeneous meso- or microporosity. In addition, WAXS shows that cellulose II hydrate structure appears and transforms to cellulose II during water evaporation, however it is not possible to determine the degree of crystallinity of the beads from the present measurements. This work sheds lights on the structural changes that occur within regenerated cellulose materials during drying and can aid in the design and application of cellulosic materials as fibers, adhesives, and membranes.

The paper presents the synthesis, the physico-chemical and the biological properties of novel hybrid materials prepared from photo-crosslinked gelatin/alginate-based hydrogels and silica particles exhibiting potential for the regeneration of bone tissue. Both alginate and gelatin were functionalized with methacrylate and methacrylamide moieties, respectively to render them photo-crosslinkable. Submicron silica particles of two sizes were dispersed within three types of polymeric sols including alginate, gelatin, and gelatin/alginate blends, which were subsequently photo-crosslinked. The swelling ratio, the gel fraction and the mechanical properties of the hybrid materials developed were examined and compared to these determined for reference hydrogel matrices. The in vitro cell culture studies have shown that the prepared materials exhibited biocompatibility as they supported both MEFs and MG-63 mitochondrial activity. Finally, the in vitro experiments performed under simulated body fluid conditions have revealed that due to inclusion of silica particles into the biopolymeric hydrogel matrices the mineralization was successfully induced.

We probe the elastic modulus of cellulose gel beads during drying by indentation with atomic force microscopy.

The drying behavior of regenerated cellulose gel beads swollen with different nonsolvents ( e.g ., water, ethanol, water/ethanol mixtures) is studied in situ on the macroscopic scale with an optical microscope as well as on nanoscale using small-angle/wide-angle X-ray scattering (SAXS/WAXS) techniques. Depending on the cellulose concentration, the structural evolution of beads during drying follows one of three distinct regimes. First, when the cellulose concentration is lower than 0.5 wt %, the drying process comprises three steps and, regardless of the water/ethanol mixture composition, a sharp structural transition corresponding to the formation of a cellulose II crystalline structure is observed. Second, when the cellulose concentration is higher than 5.0 wt %, a two-step drying process is observed and no structural transition occurs for any of the beads studied. Third, when the cellulose concentration is between 0.5 and 5.0 wt %, the drying process is dependent on the nonsolvent composition. A three-step drying process takes place for beads swollen with water/ethanol mixtures with a water content higher than 20%, while a two-step drying process is observed when the water content is lower than 20%. To describe the drying behavior governed by the cellulose concentration and nonsolvent composition, a simplified phase diagram is proposed.