No abstract

The network of stemness genes and oncogenes in human patient-specific reprogrammed cancer stem cells (CSCs) remains elusive, especially in liver cancer. HepG2-derived induced pluripotent stem cell-like cells (HepG2-iPS-like cells) were generated by introducing Yamanaka factors and the knockdown vector shTP53. They exhibited features of stemness and a higher tumorigenesis after xenograft transplantation compared with HepG2 cells. The cancerous mass of severe combined immunodeficiency (SCID) mice derived from one colony was dissected and cultured to establish reprogrammed HepG2-derived CSC-like cells (designated rG2-DC-1C). A single colony exhibited 42% occurrence of tumors with higher proliferation capacities. rG2-DC-1C showed continuous expression of the OCT4 stemness gene and of representative tumor markers, potentiated chemoresistance characteristics, and invasion activities. The sphere-colony formation ability and the invasion activity of rG2-DC-1C were also higher than those of HepG2 cells. Moreover,

It is important to develop a suitable three-dimensional scaffold for the regeneration therapy of dental pulp. In the present study, the effects of hyaluronic acid (HA) sponge on responses of the odontoblastic cell line (KN-3 cells) in vitro, as well as responses of amputated dental pulp of rat molar in vivo, were examined. In vitro, KN-3 cells adhered to the stable structure of HA sponge and that of collagen sponge. In vivo, dental pulp proliferation and vessel invasion were observed in both sponges implanted at dentin defect area above amputated dental pulp, and the cell-rich reorganizing tissue was observed in the dentin defect when HA sponge was implanted as compared with collagen sponge. Expression levels of IL-6 and TNF-alpha in KN-3 cells seeded in HA sponge were nearly the same with those in the cells seeded in collagen sponge, while the numbers (0.67 x 10(3) at 1 week and 0.7 x 10(3) at 3 weeks) of granulated leukocytes that invaded into HA sponge from amputated dental pulp was significantly lower than those (1.22 x 10(3) at 1 week and 1.1 x 10(3) at 3 weeks) of collagen sponge (p < 0.01 at 1 week and p < 0.05 at 3 weeks). These results suggest that HA sponge has an appropriate structure, biocompatibility, and biodegradation for use as a scaffold for dental pulp regeneration.

The aim of this study was to develop a three-dimensional (3D) finite element (FE) model of a sound extracted human second premolar from micro-CT data using commercially available software tools. A detailed 3D FE model of the tooth could be constructed and was experimentally validated by comparing strains calculated in the FE model with strain gauge measurement of the tooth under loading. The regression coefficient and its standard error in the regression analysis between strains calculated by the FE model and measured with strain gauge measurement were 0.82 and 0.06, respectively, and the correlation coefficient was found to be highly significant. These results suggested that an FE model reconstructed from micro-CT data could be used as a valid model to estimate the actual strains with acceptable accuracy.

A newly developed electropolishing system, equipped with an original agitation function for an electrolyte and using a safe electrolyte composed of an alcoholic solution, was applied for wrought and cast CP titanium and its alloys. Surface roughness and morphology of the polished surfaces were then examined. Under an electrolytic condition of 70-75 V, 2.0 kA/m 2 , and 30℃, wrought CP Ti and Ti-6Al-4V alloy achieved an apparent mirror-like finishing with an average surface roughness (Ra) of 0.03 and 0.12 μm respectively. Under the same condition, on the other hand, cast CP Ti and Ti-6Al-7Nb alloy produced rougher polished surfaces with average Ra values of 0.67-0.80 μm, and the finishing was apparently shiny, but not mirror-like. SEM observation of the polished surfaces showed that wrought CP Ti was even and completely featureless, while wrought Ti-6Al-4V alloy was pitted. For cast CP Ti, a needle-like phase containing traces of iron was observed on the polished surface.