This paper presents an inkjet printing method for the fabrication of entire microfluidic multianalyte chemical sensing devices made from paper suitable for quantitative analysis, requiring only a single printing apparatus. An inkjet printing device is used for the fabrication of three-dimensional hydrophilic microfluidic patterns (550-mum-wide flow channels) and sensing areas (1.5 mm x 1.5 mm squares) on filter paper, by inkjet etching, and thereby locally dissolving a hydrophobic poly(styrene) layer obtained by soaking of the filter paper in a 1 wt % solution of poly(styrene) in toluene. In a second step, the same inkjet printing device is used to print "chemical sensing inks", comprising the necessary reagents for colorimetric analytical assays, into well-defined areas of the patterned microfluidic paper devices. The arrangement of the patterns, printed inks, and sensing areas was optimized to obtain homogeneous color responses. The results are "all-inkjet-printed" chemical sensing devices for the simultaneous determination of pH, total protein, and glucose in clinically relevant concentration ranges for urine analysis (0.46-46 muM for human serum albumin, 2.8-28.0 mM for glucose, and pH 5-9). Quantitative data are obtained by digital color analysis in the L*a*b* color space by means of a color scanner and a simple computer program.

The microstructure, wettability, and thermal stability of self-assembled monolayers (SAMs) on gold generated from semifluorinated alkanethiols F(CF2)10(CH2) n SH, where n = 2, 6, 11, 17, and 33 (F10HnSH), were examined by polarization modulation infrared reflection absoprtion spectroscopy (PM-IRRAS) and dynamic contact angle measurements. Analysis by PM-IRRAS revealed that the length of the methylene spacer (Hn) influenced the tilt angle of the fluorocarbon segments in the semifluorinated SAMs. As the length of the methylene spacer was increased, the tilt angle of the perfluorocarbon moiety increased with respect to the surface normal. The longer methylene spacers (Hn, n = 11, 17, and 33) exhibited well-ordered trans-extended conformations as indicated by the position of the antisymmetric methylene band (νa CH 2 = 2919 cm-1). Shortening the length of the methylene spacer to n = 6, however, led to a decrease in conformational order (νa CH 2 = 2925 cm-1). Dynamic contact angle measurements using the Wilhelmy plate method showed that the semifluorinated SAMs were poorly wet by both water (average θa = 120°) and hexadecane (average θa = 81°). The wettability varied with the length of the methylene spacer; in particular, both the thinnest and the thickest semifluorinated SAMs (derived from F10H2SH and F10H33SH, respectively) exhibited relatively low dynamic contact angle values. In addition, the thermal stability of the semifluorinated SAMs was found to increase as the length of the methylene spacer was increased. Overall, these films exhibited remarkable resistance to thermal degradation (e.g., SAMs derived from F10H33SH sustained a relatively high contact angles after incubation at 150 °C for 1 h in air).

This paper reports on an inkjet printing method for the fabrication of lateral flow immunochromatographic devices made from a single piece of filter paper by patterning microfluidic channels and dispensing immunosensing inks, requiring only a single printing apparatus. This "paperfluidic" immunosensing device allows for a less time-consuming and more low-cost fabrication compared with the conventional immunochromatographic strips requiring multiple pads, plastic or nylon backing, and a plastic case. A sandwich immunoreaction was performed on the patterned immunosensing paper device, and the sensitivity of the device was optimized with an IgG model analyte. Inkjet-printed antibodies on the test line and the control line were immobilized by physical adsorption, resulting in a very simple fabrication method applicable for pure cellulose surfaces. The color intensity in the test line and the control line was determined both by naked eye and by means of a color scanner in combination with a simple computer program. With the resulting paperfluidic immunosensing device, human IgG concentrations at least down to 10 μg/l could be detected within 20 min. Additionally, in order to demonstrate the feasibility of a total multianalyte sensing system, a combined immuno-chemical sensing device was also fabricated by patterning an additional microfluidic channel for a chemical assay onto the same paper substrate. This low-cost multianalyte paperfluidic sensing device thus demonstrates the feasibility of simple, portable, and disposable tools for pathogen detection in the field of medical, environmental, and food analyses, possibly resulting in useful devices in remote settings and less-industrialized countries.

Human papillomavirus (HPV)-associated squamous cell carcinoma of the head and neck (SCCHN) seems to be a suitable target for cancer vaccination. HPV-encoded oncogenic proteins, such as E7, are promising tumor-specific antigens and are obligatory for tumor growth. Because few immunologic studies have analyzed the endogenous HPV-specific immune response in this subset of SCCHN patients, we studied T-cell frequencies against

No abstract