No abstract

This study describes the effects of bounce, brake, and roll behavior of a bus toward its leaf spring suspension systems. Parabolic leaf springs are designed based on vertical deflection and stress; however, loads are practically derived from various modes especially under harsh road drives or emergency braking. Parabolic leaf springs must sustain these loads without failing to ensure bus and passenger safety. In this study, the explicit nonlinear dynamic finite element (FE) method is implemented because of the complexity of experimental testing A series of load cases; namely, vertical push, wind-up, and suspension roll are introduced for the simulations. The vertical stiffness of the parabolic leaf springs is related to the vehicle load-carrying capability, whereas the wind-up stiffness is associated with vehicle braking. The roll stiffness of the parabolic leaf springs is correlated with the vehicle roll stability. To obtain a better bus performance, two new parabolic leaf spring designs are proposed and simulated. The stress level during the loadings is observed and compared with its design limit. Results indicate that the newly designed high vertical stiffness parabolic spring provides the bus a greater roll stability and a lower stress value compared with the original design. Bus safety and stability is promoted, as well as the load carrying capability.

The ride dynamic characteristics of an urban bus were investigated through simulations with suspension component characteristics and were validated through field measurements. It was performed on highway road at a constant forward speed. A random vibration bus model with two parallel tracks of terrain profile was synthesized with superposition between the left and right sides as well as time delay between front and rear. The bus frequency response model was introduced with embedded modal extraction data to enhance computation efficiency. The simulation results of the bus model were derived in terms of acceleration PSD and frequencyweighted root mean square acceleration along the vertical axes at three locations, namely, driver side, middle, and rear passenger side, to obtain the overall bus ride performance. Another two sets of new leaf spring design were proposed as suspension parameter analysis. The simulation approach provides reasonably good results in evaluating passenger perception on ride and shows that the proposed new spring design can significantly improve the ride quality of the driver and passengers.

Vehicle dynamic response of urban bus for common manoeuvres enhancing purpose has been investigated. Nowadays, increasing concerns on human driver comfort and emerging demands on suspension systems for off-road vehicles call for an effective vehicle ride dynamics model. This study devotes an analytical effort in developing a comprehensive vehicle ride dynamics simulation model. A bus simulation model which consists of two sets of different parabolic leaf springs and shock absorbers, front and rear axle, one dimensional tyres, anti-roll bars and simplified bus body with assumption the chassis is rigid has been built in finite element (FE) environment. Modal analysis is further to be performed in order to calculate the mode shapes and associated frequencies. Subsequently, suspension parameters analysis has been conducted to identify the sensitivity of every component towards the vehicle vibration behaviour. The related suspension parameters in the sensitivity analysis are parabolic leaf spring stiffness, anti-roll bars bending moment, and shock absorber damping characteristics respectively. The mode shapes and natural frequencies change due to the suspension parameters modification could be obviously visualized through finite element method. The visualization capabilities of the mode shape would provide an insight understanding of vehicle vibration behaviour in which is generally complex. The developed vehicle ride dynamics model could serve as an effective and efficient tool for predicting vehicle ride vibrations, to seek designs of primary and secondary suspensions, and to evaluate the roles of various operating conditions.

It is compulsory to have a good fatigue life to a component that is heavily subjected to cyclic loading. One of the good examples is parabolic spring, which is one of the components in suspension system for large vehicles. It serves to absorb, store and release back the damping energy due to road irregularity, bump and holes. These activities involve a lot of camber deflection that caused by the tension and compression loads. In reality, the loading that subjected to parabolic spring is variable amplitude loading, but most of the manufacturer used constant amplitude (CA) loading for the fatigue test. The objective of this paper is to relate the simulation result with the microstructure behaviour of the leaf spring that failed due to fatigue. A full scale fatigue test was carried out until that parabolic spring meet failure. In order to investigate the fatigue life, CA signal was generated based on an actual fatigue test on the parabolic spring, and it was then analysed using the FEA-based fatigue simulation. A microstructure study was then performed for both fracture and non-fracture area. From the FEA-based simulation, it gave the prediction on damage that occurred at the critical area and also the prediction on the lowest cycle with respect to the FEA model. In the actual fatigue test, the failure was occurred at the centre part of the spring, which is at bolt join of assembly hole. The microstructure analysis showed that the grain at the fracture area indicated some different from the non-fracture area in term of size, phase and precipitation of carbon.