The complexation of 6 bile salts with various methylated β-cyclodextrins was studied to elucidate how the degree and pattern of substitution affects the binding. The structures of the CDs were determined by mass spectrometry and NMR techniques, and the structures of the inclusion complexes were characterized from the complexation-induced shifts of (13)C nuclei as well as by 2D ROESY NMR. Thermodynamic data were generated using isothermal titration calorimetry. The structure-properties analysis showed that methylation at O3 hinders complexation by partially blocking the cavity entrance, while methyl groups at O2 promote complexation by extending the hydrophobic cavity. Like in the case of 2-hydroxypropylated cyclodextrins, the methyl substituents cause an increased release of ordered water from the hydration shell of the bile salts, resulting in a strong increase in both the enthalpy and the entropy of complexation with increased number of methyl substituents. Due to enthalpy-entropy compensation the effect on the stability constant is relatively limited. However, when all hydroxyl groups are methylated, the rigid structure of the free cyclodextrin is lost and the complexes are severely destabilized due to very unfavorable entropies.

The effect of the degree of substitution (DS) on the ability of hydroxypropylated β-cyclodextrin (HPβCD) to form inclusion complexes with six different bile salts, found within the intestinal tracts of rats, dogs, and humans, was studied by isothermal titration calorimetry. The composition and molecular structure of the cyclodextrin samples were characterized by MALDI-TOF mass spectrometry together with 1D and 2D-NMR, and some of the complexes were studied by 2D ROESY NMR. The stability and structure of the complexes were mainly determined by the position of hydroxyl groups on the bile salts and depended relatively little on the number of hydroxypropyl side chains on the CDs. The enthalpy and entropy of complexation exhibited a strong linear increase as the DS increased from 0 to 1, and a pronounced enthalpy-entropy compensation was observed. These observations are interpreted as an increased release of ordered water from the hydration shells of the bile salts, caused by the hydroxypropyl substituents on the rim of the CD. It is estimated that each CD hydroxypropyl substituent dehydrates a hydrophobic surface area of approximately 10 Å(2).

from over 11% [1,2] and 12% [3] up to over 13% now [4] in either tandem or single junction solar cells from benzo [1,2-b:4,5-b′] dithiophene (BDT)-based polymers as the donor material in photovoltaic (PV) devices, their limiting open-circuit voltage (V oc , below 1.00 V) is still one of the key obstacles to achieve ideally high PV performance with minimized trade-off on another characteristic features of the OPV devices, i.e., the short-circuit current density (J sc ). For the first two single junction polymer solar cells (PSCs) with PBDB-T/3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2′,3′-d′]-s-indaceno[1,2-b:5,6-b′]dithiophene (ITIC) and PBDT-T/IT-M as active layer materials, respectively, their photon energy loss (defined as E Loss = E g − eV oc , [5,6] whereas E g refers to the band gap energy difference between the energy level of highest occupied molecular orbital (HOMO) and lowest unoccupied mole cular orbital (LUMO)) has been pronounced as 0.66 and 0.69 eV, respectively, which is still above the empirically optimized level of 0.60 eV. [7] Despite their breaking PCE values, these nonideally low E Loss still reflect the imperfect molecular design of the PBDB-T backbone structure for ideal control on their HOMO/LUMO levels.

No abstract

A method called Dock'n'Flash was developed to offer site-specific capture and direct UVA-induced photocoupling of recombinant proteins. The method involves the tagging of recombinant proteins with photoreactive p-benzoyl-L-phenylalanine (pBpa) by genetic engineering. The photoreactive pBpa tag is used for affinity capture of the recombinant protein by beta-cyclodextrin (beta-CD), which provides hydrogen atoms to be abstracted in the photocoupling process. To exemplify the method, a recombinant, folded, and active N27pBpa mutant of cutinase from Fusarium solani pisi was produced in E. coli. Insertion of pBpa was verified by matrix-assisted laser desorption ionization time-of-flight (MALDI-TOF) mass spectroscopy. A molecular dynamic simulation, with water as solvent, showed high solvent accessibility of the pBpa benzophenone group in N27pBpa-cutinase mutant. The formation of an inclusion complex between the benzophenone group of N27pBpa-cutinase and beta-CD was shown, and an apparent K(d) of 1.65 mM was determined using (1)H NMR. Photocoupling of beta-CD to N27pBpa-cutinase in a 1:1 ratio, upon UVA irradiation at 360 +/- 20 nm, was shown by MALDI-TOF mass spectroscopy. UVA photoimmobilization of N27pBpa-cutinase on quartz slides coated with beta-CD was achieved from liquid or dry films by total internal reflection fluorescence (TIRF). The Dock'n'Flash method offers a solution for direct photocoupling and patterning of recombinant proteins onto surfaces with site-specific attachment.