The paper considers large-panel constructive system of multi-storey buildings and its industrial basis creates conditions for intensive volume growth in house construction. Application of hollow-core panels are recommended as floor slabs that allows to increase a distance between bearing walls, to improve planning solutions, and also significantly to increase thermal and sound protection properties of floor discs (coatings). Keyed joints having the highest resistance to shearing forces are used to ensure joint action of the slabs with wall panels. A supporting unit of floor elements in the precast-monolithic constructive system ARKOS by means of concrete keys is considered as a prototype of the considered joint. In order to increase a bearing capacity and improve reliability of joints it is envisaged to reinforce keys with space frames. Improvement of joint units is possible to carry out with due account of total number of the factors influencing on strength. Poltava National Technical University named after Yuri Kondratyuk has developed a general methodology for assessment of bearing capacity in keyed joints which is based on the variational method in the theory of concrete plasticity and reflects specificity of stress-strain state of the failure zone. For experimental verification of this methodology investigations have been carried out with the purpose to test operation of keys when they are reinforced in mid-height and reinforcement is distributed in two tiers. The observed experimental fracture pattern in the specimens has confirmed kinematic schemes accepted for calculations and comparative analysis of experimental and theoretical values points to their closeness. Two-level reinforcement significantly improves plastic properties of concrete keys and excludes brittle failure. The proposed design of the joint unit for floor slabs with wall panels is characterized by the ratio of key dimensions and shape of reinforcing cages in the form of hollow cylinders which ensure higher strength and seismic resistance of a joint.

The connections ensure teamwork under the load of buildings and structures bearing elements. Joints distraction leads to a change in the structures support conditions and their design schemes. Keyed joints are the most effective under significant shear force action because they have high shear resistance. This makes it necessary to further improve their design solutions. In the article the experimental study results of multikeyed joints two series are presented. The joint models were tested in the department laboratory of reinforced concrete and stone structures and resistance of materials Poltava National Technical Yuri Kondratyuk University. The keyed profile (key’s depth to height ratio and load application surface angle), reinforcement (quantity of reinforcement and its location character), seam width, keys number were varied in experiments. Heavy-weight concrete, expanded clay concrete and polypropylene fiber concrete were used for the samples manufacture. In experiments the influence of one of listed factors and their combinations for bearing capacity were studied. The concrete and reinforcement strains, distraction character, the failure load were studied. The influence degree analysis of the factors determining the strength was carried out. The design joints parameters that correspond to maximum strength were determined.

Abstract. The two-dimensional concrete elements under the action of one-sided central crushing often occurs. For them, the strength problems are solved on the basis of the concrete ideal plasticity theory variational method with application of discontinuous velocities functions. The method takes into account the influence on concrete elements strength the compressive strength and tensile strength of concrete. It also takes the ratio of a sample height to the crushing platform length and friction coefficient between a surface of element and a load punch if it′s necessary. The results of experimental researches were confirmed the assumed in the theoretical solution the kinematical schemes of elements failure. Higher convergence of theoretical strength with tested is received. The calculation sequence of the concrete element under one-sided central crushing is described. The joint calculation of all factors that determine the strength opens the possibility of more accurate assessment and improvement on its basis of structural solutions of concrete elements under the local compressive load.

Based on experiments results brittle duralumin samples, effect on stresses concrete (mortar) strength caused by non-uniform cross-section shrinkage (when dried) or expanding (when moistened) was inevitable. Various authors’ experiments results diversity on concrete (mortar) tensile strength of moistening and drying effect were analyzed. Reasons for increasing air-dry concrete (mortar) strength storage at beginning of humidification were explained. Wetting sample duration (intensity) effect on concrete strength was analyzed in detail and opposite results causes on concrete strength moistening (drying) effects were obtained and justified.

Application boundaries of the truss analogy and disk model methods to the strength calculation of reinforced concrete flexuralelements inclined sections are established. Areas of structures failure by virtual compressed element (inclined strip) andcompressed zone over dangerous inclined crack under the shear force are determined. The criterion of minimum limit force,which is perceived by the elements, is applied. Influence of concrete class, relative shear span and transverse reinforcementintensity on elements strength based on variational method in plasticity theory is specified. The data concerning the values ofthe transverse reinforcement coefficient at the boundaries of the failure from shear within the inclined strip and compressedzone over the dangerous crack are obtained.