Under illumination of light-emitting diode (LED) or sunlight, the green color of all-inorganic CsPbBr perovskite nanocrystals (CPB-NCs) often quickly changes to yellow, followed by large photoluminescence (PL) loss. To figure out what is happening on CPB-NCs during the color change process, the morphology, structure, and PL evolutions are systematically investigated by varying the influence factors of illumination, moisture, oxygen, and temperature. We find that the yellow color is mainly originated from the large CPB crystals formed in the illumination process. With maximized isolation of oxygen for the sandwiched film or the uncovered film stored in nitrogen, the color change can be dramatically slowed down whether there is water vapor or not. Under dark condition, the PL emissions are not significantly influenced by the varied relative humidity (RH) levels and temperatures up to 60 °C. Under the precondition of oxygen or air, color change and PL loss become more obvious when increasing the illumination power or RH level, and the large-sized cubic CPB crystals are further evolved into the oval-shaped crystals. We confirm that oxygen is the crucial factor to drive the color change, which has the strong synergistic effect with the illumination and moisture for the degradation of the CPB film. Meanwhile, the surface decomposition and the increased charge trap states occurred in the formed large CPB crystals play important roles for the PL loss.

No abstract

We successfully prepared QDs incorporated into a silica/alumina monolith (QDs-SAM) by a simple sol-gel reaction of an Al-Si single precursor with CsPbBr QDs blended in toluene solution, without adding water and catalyst. The resultant transparent monolith exhibits high photoluminescence quantum yields (PLQY) up to 90 %, and good photostability under strong illumination of blue light for 300 h. We show that the preliminary ligand exchange of didodecyl dimethyl ammonium bromide (DDAB) was very important to protect CsPbBr QDs from surface damages during the sol-gel reaction, which not only allowed us to maintain the original optical properties of CsPbBr QDs but also prevented the aggregation of QDs and made the monolith transparent. The CsPbBr QDs-SAM in powder form was easily mixed into the resins and applied as color-converting layer with curing on blue light-emitting diodes (LED). The material showed a high luminous efficacy of 80 lm W and a narrow emission with a full width at half maximum (FWHM) of 25 nm.

Achieving good stability while maintaining excellent properties is one of the main challenges for enhancing the competitiveness of luminescent perovskite CsPbX 3 (X=Cl, Br, I) nanocrystals (NCs). Here, we propose a facile strategy to synthesize ceramic-like stable and highly luminescent CsPbBr 3 NCs by encapsulating them into silica derived from molecular sieve templates at high temperature (600-900 o C). The obtained CsPbBr 3 -SiO 2 powders not only show high photoluminescence quantum yield (~71%), but also show an exceptional stability comparable to the ceramic Sr 2 SiO 4 :Eu 2+ green phosphor. They can maintain 100% of their photoluminescence value under illumination on blue light-emitting diodes (LEDs) chips (20 mA, 2.7 V) for 1000 h, and can also survive in a harsh hydrochloric acid aqueous solution (1 M) for 50 days. We believe that the above robust stabilities will significantly enhance the potential of perovskite CsPbX 3 NCs to be practically applied in LEDs and backlight displays.

We successfully prepared QDs incorporated into as ilica/alumina monolith (QDs-SAM) by as imple sol-gel reaction of an Al-Si single precursor with CsPbBr 3 QDs blended in toluene solution, without adding water and catalyst. The resultant transparent monolith exhibits high photoluminescence quantum yields (PLQY) up to 90 %, and good photostability under strong illumination of blue light for 300 h. We show that the preliminary ligand exchange of didodecyl dimethyl ammonium bromide (DDAB) was very important to protect CsPbBr 3 QDs from surface damages during the sol-gel reaction, whichn ot only allowed us to maintain the original optical properties of CsPbBr 3 QDs but also prevented the aggregation of QDs and made the monolith transparent. The CsPbBr 3 QDs-SAM in powder form was easily mixed into the resins and applied as color-converting layer with curing on blue light-emitting diodes (LED). The material showed ahigh luminous efficacy of 80 lm W À1 and an arrowe mission with afull width at half maximum (FWHM) of 25 nm.