Surface dissolution of manganese is a long-standing issue hindering the practical application of spinel LiMn2O4 cathode material, while few studies concerning the crystal structure evolution at the surface area have been reported. Combining X-ray photoelectron spectroscopy, electron energy loss spectroscopy, scanning transmission electron microscopy, and density functional theory calculations, we investigate the chemical and structural evolutions on the surface of a LiMn2O4 electrode upon cycling. We found that an unexpected Mn3O4 phase was present on the surface of LiMn2O4 via the application of an advanced electron microscopy. Since the Mn3O4 phase contains 1/3 soluble Mn2+ ions, formation of this phase contributes significantly to the Mn2+ dissolution in a LiMn2O4 electrode upon cycling. It is further found that the Mn3O4 appears upon charge and disappears upon discharge, coincident with the valence change of Mn. Our results shed light on the importance of stabilizing the surface structure of cathode material, especially at the charged state. The understanding of the manganese dissolution reaction that occurs in the LiMn2O4 can certainly be extended to other oxide cathodes.

Application of high-voltage spinel LiNi 0.5 Mn 1.5 O 4 cathode material is the closest and the most realistic approach to meeting the midterm goal of lithium-ion batteries for electric vehicles (EVs) and plug-in hybrid electric vehicles (HEVs). However, this application has been hampered by long-standing issues, such as capacity degradation and poor first-cycle Coulombic efficiency of LiNi 0.5 Mn 1.5 O 4 cathode material. Although it is well-known that the structure of LiNi 0.5 Mn 1.5 O 4 into which Li ions are reversibly intercalated plays a critical role in the above issues, performance degradation related to structural changes, particularly in the first cycle, are not fully understood. Here, we report detailed investigations of local atomic-level and average structure of LiNi 0.5 Mn 1.5 O 4 during first cycle (3.5−4.9 V) at room temperature. We observed two types of local atomic-level migration of transition metals (TM) ions in the cathode of a well-prepared LiNi 0.5 Mn 1.5 O 4 //Li half-cell during first charge via an aberration-corrected scanning transmission electron microscopy (STEM). Surface regions (∼2 nm) of the cycled LiNi 0.5 Mn 1.5 O 4 particles show migration of TM ions into tetrahedral Li sites to form a Mn 3 O 4 -like structure. However, subsurface regions of the cycled particles exhibit migration of TM ions into empty octahedral sites to form a rocksalt-like structure. The migration of these TM ions are closely related to dissolution of Ni/Mn ions and building-up of charge transfer impedance, which contribute significantly to the capacity degradation and the poor first-cycle Coulombic efficiency of spinel LiNi 0.5 Mn 1.5 O 4 cathode material. Accordingly, we provide suggestions of effective stabilization of LiNi 0.5 Mn 1.5 O 4 structure to obtain better electrochemical performance.

The microstructure and mechanical properties of the solid electrolyte interphase (SEI) in non-aqueous lithium ion batteries are key issues for understanding and optimizing the electrochemical performance of lithium batteries. In this report, the three-dimensional (3D) multi-layered structures and the mechanical properties of the SEI formed on a silicon anode material for next generation lithium ion batteries have been visualized directly for the first time, through a scanning force spectroscopy method. The coverage of the SEI on silicon anodes is also obtained through 2D projection plots. The effects of temperature and the function of additives in the electrolyte on the SEI can be understood accordingly. A modified model about dynamic evolution of the SEI on the silicon anode material is also proposed, which aims to explain why the SEI is very thick and how the multi-layered structure is formed and decomposed dynamically.