From their discovery, antibiotics have significantly improved clinical treatments of infections, thus leading to diminishing morbidity and mortality in critical care patients, as well as surgical, transplant and other types of medical procedures. In contemporary medicine, a significant debate regarding the development of multi-drug resistance involves all types of pathogens, especially in acute care hospitals due to suboptimal or inappropriate therapy. The possibility of nanotechnology using nanoparticles as matrices to encapsulate a lot of active molecules should increase drug efficacy, limit adverse effects and be an alternative helping to combat antibiotic resistance. The major aim of this study was to obtain and to analyze physico-chemical features of chitosan used as a drug-delivery system in order to stop the antibiotic resistance of different pathogens. It is well known that World Health Organization stated that multidrug resistance is one of the most important health threats worldwide. In last few years, nano-medicine emerged as an improved therapy to combat antibiotic-resistant infections agents. This work relies on enhancement of the antimicrobial efficiency of ceftriaxone against gram(+) and gram(−) bacteria by antibiotic encapsulation into chitosan nanoparticles. Physicochemical features of ceftriaxone-loaded polymer nanoparticles were investigated by particle size distribution and zeta potential, Fourier-transform infrared spectroscopy (FTIR), Thermal Gravimetric Analysis (TG/TGA), Scanning Electron Microscopy (SEM) characteristics techniques. The obtained results revealed an average particle size of 250 nm and a zeta potential value of 38.5 mV. The release profile indicates an incipient drug deliverance of almost 15%, after 2 h of approximately 83%, followed by a slowed drug release up to 24 h. Characteristics peaks of chitosan were confirmed by FTIR spectra indicating a similar structure in the case of ceftriaxone-loaded chitosan nanoparticles. A good encapsulation of the antibiotic into chitosan nanoparticles was also provided by thermo-gravimetric analysis. Morphological characteristics shown by SEM micrographs exhibit spherical nanoparticles of 30–250 nm in size with agglomerated architectures. Chitosan, a natural polymer which is used to load different drugs, provides sustained and prolonged release of antibiotics at a specific target by possessing antimicrobial activity against gram(+) and gram(−) bacteria. In this research, ceftriaxone-loaded chitosan nanoparticles were investigated as a carrier in antibiotic delivery.

Recently, nanotechnology research studies have been proven that use of various nanoparticles as drug delivery systems to target and to annihilate pathogenic microorganisms may be a good solution for prevention and treatment of severe infection. In the last few years, antimicrobial drug encapsulation into nano-sized systems has materialized as a promising alternative that increased drug efficacy and minimized adverse effects. Physicochemical properties of erythromycin-loaded polymer nanoparticles were assessed using particle size distribution, HPLC, FTIR, TG/DTA, and SEM characterization techniques. The as-prepared samples exhibited an average particle size of 340 and 270 nm, respectively, with erythromycin content of 99.7% in both samples. From the release profile of erythromycin from PLA/PLGA, a prolonged drug release can be observed from both Ery-PLA and Ery-PLGA nanostructures. Morphology images exhibited spherical, rigid, and ring-shaped nanoparticles. Thermal analytical study in the case of Ery-PLA and Ery-PLGA samples showed that pure drug has an endothermic peak at around 150 °C assigned to a melting point. The antibiotic melting peak disappeared for both antibiotic-loaded PLA and PLGA nanoparticles thermographs, denoting the presence of erythromycin. This indicates that the antibiotic is uniformly dispensed throughout the host polymer matrix at nanometer scale. FTIR spectra of Ery-PLA and Ery-PLGA nano-architectures with almost similar peaks indicated no alteration in chemical structure of drug-loaded polymer nanoparticles.

The renin-angiotensin system (RAS) is one of the biggest challenges of cardiovascular medicine. The significance of the RAS in the chronic progression of SARS-CoV-2 infection and its consequences is one of the topics that are currently being mostly discussed. SARS-CoV-2 undermines the balance between beneficial and harmful RAS pathways. The level of soluble ACE2 and membrane-bound ACE2 are both upregulated by the endocytosis of the SARS-CoV-2/ACE2 complex and the tumor necrosis factor (TNF)-α-converting enzyme (ADAM17)-induced cleavage. Through the link between RAS and the processes of proliferation, the processes of fibrous remodelling of the myocardium are initiated from the acute phase of the disease, continuing into the long COVID stage. In the long term, RAS dysfunction may cause an impairment of its beneficial effects leading to thromboembolic processes and a reduction in perfusion of target organs. The main aspects of ACE2—a key pathogenic role in COVID-19 as well as the mechanisms of RAS involvement in COVID cardiovascular injuries are studied. Therapeutic directions that can be currently anticipated in relation to the various pathogenic pathways of progression of cardiovascular damage in patients with longCOVID have also been outlined.

The aim of the paper is to identify the of optimal plastic type used in obtaining thoraco-lumbar orthoses - used in the treatments of comminutive fracture, of burst fracture type of the vertebrae in the lumbar area. For this purpose, with the help of Finite Element Analysis (FEA), a theoretical study was carried out on the influence of elastic properties of plastics, used in the achieving of lumbar orthoses, on the state of tension and on the local displacements of the bone fragments from the traumatized area under the condition of the movement from the base of extension and flexion. In the study the force of flexion, the force of extension and the elastic modulus of plastic material varied on three levels. The theoretical results obtained were completed with clinical trials carried out on a total of 26 patients who suffer thoraco-lumbar comminutive fracture, burst fractures type, at vertebra T11 and were immobilized in Boston-type plastic orthoses made of: polypropylene (PP), rigid vinyl polychloride (PVC-D) and polytetrafluoroethylene (PTFE). As a result of observations, it was found that the use of an orthesis made from rigid plastic material, although it appears higher stresses in the traumatized zone, the displacements of bone fragments are smaller, the pains is higher in the fractured zone, the angle of kyphosis (LKA) close to the normal value and a better mobility of the spine (ODI indicator).