The surface of poly(L-lactide) (PLLA) films deposited on glass coverslips was modified with poly(DL-lactide) (PDLLA), or 1:4 mixtures of PDLLA and PDLLA-b-PEO block copolymers, in which either none, 5% or 20% of the copolymer molecules carried a synthetic extracellular matrix-derived ligand for integrin adhesion receptors, the GRGDSG oligopeptide, attached to the end of the PEO chain. The materials, perspective for vascular tissue engineering, were seeded with rat aortic smooth muscle cells (11,000 cells/cm(2)) and the adhesion, spreading, DNA synthesis and proliferation of these cells was followed on inert and bioactive surfaces. In 24-h-old cultures in serum-supplemented media, the number of cells adhering to the PDLLA-b-PEO copolymer was almost eight times lower than that on the control PDLLA surface. On the surfaces containing 5% and 20% GRGDSG-PEO-b-PDLLA copolymer, the number of cells increased 6- and 3-fold respectively, compared to the PDLLA-b-PEO copolymer alone. On PDLLA-b-PEO copolymer alone, the cells were typically round and non-spread, whereas on GRGDSG-modified surfaces the cell spreading areas approached those found on PDLLA, reaching values of 991 microm(2) and 611 microm(2) for 5% and 20% GRGDSG respectively, compared to 958 microm(2) for PDLLA. The cells on GRGDSG-grafted copolymers were able to form vinculin-containing focal adhesion plaques, to synthesize DNA and even proliferate in a serum-free medium, which indicates specific binding to the GRGDSG sequences through their adhesion receptors.

No abstract

No abstract

To modify the surface of poly(L-lactide) (PLA) supports, we have investigated the feasibility to deposit on the PLA surface Langmuir-Blodgett films of amphiphilic block copolymers based on poly(L-lactide). AB and ABA block copolymers were prepared with PLA as the A block and either poly(ethylene oxide), alpha-methoxy-omega-hydroxy poly(ethylene oxide), alpha-carboxy-omega-hydroxy poly(ethylene oxide) or poly(L-aspartic acid) as the B blocks. Films with phase-separated hydrophilic and hydrophobic blocks in a bilayer "brush" structure were prepared by compression of the copolymer Langmuir films on the water/air interface. The interfacial behavior of the monolayers and the effect of the copolymer composition on the phase separation was followed by measurements of the surface-pressure/area isotherms using a Langmuir trough and by contact angle measurement of deposited Langmuir-Blodgett (LB) films. The phase separation of the hydrophilic and PLA blocks is more effective in diblock AB copolymers compared with triblock ABA copolymers. The presence of ionic groups in the hydrophilic chains facilitates penetration of hydrophilic segments into the water subphase. Dynamic contact angle measurements were used to study the stability of the LB-films transferred on the PLA support and the changes in the surface properties upon incubation of surfaces in water.

The porous polymer foams act as a template for neotissuegenesis in tissue engineering, and, as a reservoir for cell transplants such as pancreatic islets while simultaneously providing a functional interface with the host body. The fabrication of foams with the controlled shape, size and pore structure is of prime importance in various bioengineering applications. To this end, here we demonstrate a thermally induced phase separation (TIPS) based facile process for the fabrication of polymer foams with a controlled architecture. The setup comprises of a metallic template bar (T), a metallic conducting block (C) and a non-metallic reservoir tube (R), connected in sequence T-C-R. The process hereinafter termed as Dip TIPS, involves the dipping of the T-bar into a polymer solution, followed by filling of the R-tube with a freezing mixture to induce the phase separation of a polymer solution in the immediate vicinity of T-bar; Subsequent free-drying or freeze-extraction steps produced the polymer foams. An easy exchange of the T-bar of a spherical or rectangular shape allowed the fabrication of tubular, open- capsular and flat-sheet shaped foams. A mere change in the quenching time produced the foams with a thickness ranging from hundreds of microns to several millimeters. And, the pore size was conveniently controlled by varying either the polymer concentration or the quenching temperature. Subsequent in vivo studies in brown Norway rats for 4-weeks demonstrated the guided cell infiltration and homogenous cell distribution through the polymer matrix, without any fibrous capsule and necrotic core. In conclusion, the results show the “Dip TIPS” as a facile and adaptable process for the fabrication of anisotropic channeled porous polymer foams of various shapes and sizes for potential applications in tissue engineering, cell transplantation and other related fields.