The aim of the present study was to evaluate microhardness, mineral recovery and the enamel surface after the application of topical fluoride to artificial dental caries. Twenty-five bovine enamel blocks were prepared for artificial caries-like lesions and randomly divided into five groups (n=5): untreated (C control), 1.23% acidulated phosphate fluoride gel (APG), 2% neutral fluoride gel (NFG), 1.23% acidulated fluoride mousse (AFM) and fluoride varnish (5% Duraphat, DFV). Knoop microhardness (KHN) was evaluated after 7 and 14 days of treatment as well as 1 week after 28 days of treatment. Electron and confocal microscopy and energy dispersive spectroscopy were performed. KHN data were treated with two-way ANOVA (material×time) and Tukey's test at a 5% significance level. Differences were found among groups over time (p<0.001). Microhardness varied after 7 and 14 days of treatment and remained stable 1 week after 28 days of treatment. Mineral recovery and enamel topography varied among groups, with the fluoride varnish achieving the most uniform topography.

This study aimed to evaluate microhardness of a dentifrice containing fluoride and arginine compared to a positive control (fluoride only) and a negative control (no fluoride) on sound and demineralized bovine enamel surfaces. Specimens were randomly assigned to different treatments that included daily pH cycling and brushing three times a day with one of the following dentifrices (n = 8): Neutraçucar (arginine and fluoride), Colgate Total 12 (fluoride) and My First Colgate (no fluoride). Enamel carious lesions were artificially created one week before the beginning of these treatments (demineralized bovine enamel (DE) groups). The same groups were also tested in sound enamel (sound bovine enamel (SE) groups). Microhardness was measured at baseline and after one, two, and five weeks of treatment using a Knoop indenter. Statistical analysis involved two-way Analysis of Variance (ANOVA) and Tukey’s test. After five weeks, both Total 12 and Neutraçucar had increased the microhardness of DE specimens (p < 0.05). Only Neutraçucar had increased the microhardness of the sound enamel after five weeks of treatment. Thus, it could be concluded that arginine-based dentifrices increase the microhardness of sound and demineralized bovine enamel surfaces.

No abstract

Objective To evaluate the influence of ultrapulsed CO2 laser in combination with commercial fluoride products in order to verify the increase of microhardness of artificial enamel caries lesions. Materials and Methods Bovine enamel specimens were prepared, and artificial enamel caries lesions were created. Teeth were randomly divided into 5 groups (n=10): treated with laser (L), laser + neutral fluoride gel 2% (LNF), laser + acidulated phosphate fluoride gel 1.23% (LAFG), laser + acidulated fluoride mousse 1.23% (LAFM), and laser + fluoride varnish 5% (LFV). Microhardness was evaluated at baseline, after caries induction, after CO2 laser irradiation + fluoride treatment in the 1st week, and after fluoride treatment at 3rd and 5th week. Results There was a decrease in microhardness in all groups after artificial enamel caries lesion formation; no increase in microhardness was found in the first and third weeks in all groups (p > 0.05). In the fifth week, an increase in microhardness occurred in all groups (p < 0.05). Conclusion Although CO2 laser irradiation in combination with different commercial fluoride products was capable of increasing microhardness on enamel caries lesions in bovine tooth enamel it is necessary to confirm these results by testing the isolated effect of fluoride on enamel surface microhardness. Also, although microhardness was higher in the fluoride varnish group than in the other groups in the fifth week it is not possible to discard the best effect of fluoride varnish treatment on absence of artifacts that may occur with the other fluoride treatments. Clinical Relevance In order to prove that CO2 laser may contribute to an increase in microhardness when applied to enamel lesions in combination with different commercial fluoride products it is necessary to conduct additional studies. Also, higher microhardness of fluoride varnish group should be carefully considered.

No abstract