Buckling of slender beam-columns subject to axial compressive loads represents a critical design constraint for light-weight structures. Active buckling control provides a possibility to stabilize slender beam-columns by active lateral forces or bending moments. In this paper, the potential of active buckling control of an axially loaded beam-column with circular solid cross-section by piezo-elastic supports is investigated experimentally. In the piezo-elastic supports, lateral forces of piezoelectric stack actuators are transformed into bending moments acting in arbitrary directions at the beam-column ends. A mathematical model of the axially loaded beam-column is derived to design an integral linear quadratic regulator (LQR) that stabilizes the system. The effectiveness of the stabilization concept is investigated in an experimental test setup and compared with the uncontrolled system. With the proposed active buckling control it is possible to stabilize the beam-column in arbitrary lateral direction for axial loads up to the theoretical critical buckling load of the system.

Undesired vibration may occur in lightweight structures due to excitation and low damping. For the purpose of lateral vibration attenuation in beam structures, piezoelectric transducers shunted to negative capacitances can be an appropriate measure. In this paper, a new concept for lateral vibration attenuation by integrated piezoelectric stack transducers in the elastic support of a beam with circular cross-section is presented. In the piezoelastic support, bending of the beam in an arbitrary direction is transformed into a significant axial deformation of three stack transducers and, thus, the beam's surface may remain free from transducers. For multimodal vibration attenuation, each piezoelectric transducer is shunted to a negative capacitance. It is shown by numerical simulation and experiment that the concept of an elastic beam support with integrated shunted piezoelectric stack transducers is capable of reducing the lateral vibration of the beam in an arbitrary direction.

Buckling of slender bars subject to axial compressive loads represents a critical design constraint for light-weight truss structures. Active buckling control by actuators provides a possibility to increase the maximum bearable axial load of individual bars and, thus, to stabilize the truss structure.For reasons of cost, it is in general not economically viable to use such actuators in each bar of the truss structure. Hence, it is an important practical question where to place these active bars. Optimized structures, especially when coupled with active elements to further decrease the number of necessary bars, however, lead to designs, which, while cost-efficient, are especially prone to bardamages, caused, e.g., by material failures. Therefore, this paper presents a mathematical optimization approach to optimally place active bars for buckling control in a way that secures both buckling and general stability constraints even after failure of any combination of a certain number of bars. This allows us to increase the resilience of the system and guarantee stable behavior even in case of failures.

For slender beam-columns loaded by axial compressive forces, active buckling control provides a possibility to increase the maximum bearable axial load above that of a purely passive structure. In this paper, an approach for gain-scheduled buckling control of a slender beam-column with circular cross-section subject to time-varying axial loads is investigated experimentally. Piezo-elastic supports with integrated piezoelectric stack actuators at the beam-column ends allow an active stabilization in arbitrary lateral directions. The axial loads on the beam-column influence its lateral dynamic behavior and, eventually, cause the beam-column to buckle. A reduced modal model of the beam-column subject to axial loads including the dynamics of the electrical components is set up and calibrated with experimental data. Particularly, the linear parameter-varying open-loop plant is used to design a model-based gain-scheduled buckling control that is implemented in an experimental test setup. The beam-column is loaded by ramp- and step-shaped time-varying axial compressive loads that result in a lateral deformation of the beam-column due to imperfections, such as predeformation, eccentric loading or clamping moments. The lateral deformations and the maximum bearable loads of the beam-column are analyzed and compared for the beam-column with and without gain-scheduled buckling control or, respectively, active and passive configuration. With the proposed gain-scheduled buckling control it is possible to increase the maximum bearable load of the active beam-column by 19% for ramp-shaped axial loads and to significantly reduce the beam-column deformations for step-shaped axial loads compared to the passive structure.

Beams in lightweight truss structures are subject to axial and lateral loads that may lead to undesired structural vibration or failure by buckling. The axial and lateral forces may be transferred via the truss supports that offer possibilities for state control of single beams and larger structures. In earlier own studies, the concept of a piezo-elastic support for active buckling control and resonant shunt damping has been investigated. An elastic spring element is used to allow a rotation in the beam's bearing in any plane perpendicular to the beam's longitudinal axis. The rotation is laterally transferred to an axial displacement of piezoelectric stack transducers that are either used to generate active lateral forces for active buckling control or to attenuate vibrations with a resonant shunt. In this paper, the model verification and validation of the elastic properties of the piezo-elastic support for passive and active structural control of beams with circular cross-section is presented. The rotational and lateral spring element stiffness is investigated numerically and experimentally and the existing models are updated in the verification process. The model is validated by comparing the numerical results and experimental ability for vibration attenuation.