The paper presents results of the incorporation of the harmonic nonlinear method into an existing turbomachinery Navier-Stokes code. This approach, introduced by He and Ning in 1998, can be considered as a bridge between classical steady state and full unsteady calculations, providing an approximate unsteady solution at affordable calculation costs. The unsteady flow perturbation is Fourier decomposed in time, and by a casting in the frequency domain transport equations are obtained for each time frequency. The user controls the accuracy of the unsteady solution through the order of the Fourier series. Alongside the solving of the time-averaged flow steady-state equations, each frequency requires the solving of two additional sets of conservation equations (for the real and imaginary parts of each harmonic). The method is made nonlinear by the injection of the so-called deterministic stresses, resulting from all the solved frequencies, into the time-averaged flow solver. Because of the transposition to the frequency domain, only one blade channel is required like a steady flow simulation. The presented method also features a new improved treatment that enhances the flow continuity across the rotor/stator interface by a reconstruction of the harmonics and the time-averaged flow on both sides of the interface. A non-reflective treatment is applied as well at each interface. Validation for analytical and turbomachinery test cases are presented. In particular, results are compared between the harmonic method, steady-state mixing plane and full unsteady calculations. The comparison with the reference full unsteady calculation provides a quantitative indication of the accuracy of the approach, as well as the significant gain in CPU time, whereas the comparison with classical quasi-steady state solutions indicates the gain of accuracy. A multistage compressor flow is also presented to show the capabilities of the method.

This article presents the potential of active flow control to increase the aerodynamic performance of highly loaded turbomachinery compressor blades. Experimental investigations on a large-scale compressor cascade equipped with 30 synthetic jet actuators mounted to the sidewalls and the blades themselves have been carried out. Results for a variation of the inflow angle, the jet amplitude, and the actuation frequency are presented. The wake measurements show total pressure loss reductions of nearly 10 per cent for the synthetic jet actuation. An efficiency calculation reveals that the energy saved by actuation is nearly twice the energy consumption of the synthetic jets.

This paper presents results of numerical investigations carried out to explore the benefit of end wall boundary layer removal from critical regions of highly loaded axial compressor blade rows. At the loading level of modern aero engine compressors, the performance is primarily determined by three-dimensional (3D) flow phenomena occurring in the end wall regions. Three-dimensional Navier–Stokes simulations were conducted on both a rotor and a stator test case in order to evaluate the basic effects and the practical value of bleeding air from specific locations at the casing end wall. The results of the numerical survey demonstrated substantial benefits of relatively small bleed rates to the local flow field and to the performance of the two blade rows. On the rotor, the boundary layer fluid was removed from the main flow path through an axisymmetric slot in the casing over the rotor tip. This proved to give some control over the tip leakage vortex flow and the associated loss generation. On the stator, the boundary layer fluid was taken from the flow path through a single bleed hole within the passage. Two alternative off-take configurations were evaluated, revealing a large impact of the bleed hole shape and the location on the cross-passage flow and the suction side corner separation. On both blade rows investigated, rotor and stator, the boundary layer removal resulted in a reduction of the local reverse flow, blockage, and losses in the respective near-casing region. This paper gives insight into changes occurring in the 3D passage flow field near the casing and summarizes the effects on the radial matching and pitchwise-averaged performance parameters, namely loss and deviation of the rotor and stator when suction is active. Primary focus is put on the aerodynamics in the blade rows in the main flow path; details of the internal flow structure within the bleed off-take cavities/ports are not discussed here.

This paper presents experimental and numerical results for a highly loaded, low speed, linear compressor cascade with active flow control. Three active flow control concepts employing steady jets, pulsed jets, and zero mass flow jets (synthetic jets) are investigated at two different forcing locations: at the end walls and the blade suction side. Investigations are performed at the design incidence for jet-to-inlet velocity ratios of approximately 0.7 to 3.0 and two different Reynolds numbers. Detailed flow field data are collected using a five-hole pressure probe, pressure tabs on the blade surfaces, and time-resolved particle image velocimetry. Unsteady Reynolds-Averaged Navier-Stokes simulations are performed for a wide range of flow control parameters. The experimental and numerical results are used to understand the interaction between the jet and the passage flow. Variation of jet amplitude, forcing frequency and blowing angle of the different control concepts at both locations allows determination of beneficial control parameters and offers a comparison between similar control approaches. This paper combines the advantages of an expensive yet reliable experiment and a fast but limited numerical simulation. Excellent agreement in control effectiveness is found between experiment and simulation.

No abstract