This paper has investigated the porosity of knitted fabrics using digital imaging techniques. A number of different methods have been proposed to determine the porosity of knitted fabrics, which include digital imaging, geometrical modeling, and air permeability. Digital imaging is an adequate technique to determine the porosity of high-porosity fabrics. In this work, eight types of knitted structures with eight different stitch lengths were produced on a flat-bed knitting machine. Porosity was determined using digital imaging techniques based on the method of threshold and pixel count, using a computer program developed for this work.

The present paper attempts to investigate the relationship between fabric porosity and light permeability of the knitted structures, namely, rib 1 × 1, rib 2 × 1, single jersey, and plain structure. The rationale is that pores (in a fabric) would allow light to pass through but at the same time provide a quantitative assessment of the UV light permeability of the knitted fabrics, an indication of the protective capacity of the fabrics against UV radiation. The porosity and corresponding light permeability of the knitted structures were measured after varying the following knitting parameters: stitch length, stitch density, and tension on the machine. Furthermore, this work has enabled the development of an apparatus that can measure the amount of light transmitted through the knitted fabrics. The results generated by the equipment were validated through the use of regression equations.

Purpose The thermophysiological comfort of fabrics is prerequisite as customers covet adequate moisture, heat management-supported and UV protective clothing that measure up to their levels of activities and environmental conditions. Hitherto, scant tasks have been reported with the purpose of engineering both comfort and UV protection simultaneously. From that vantage point, the objective of this work is to develop a model for optimum UPF, air permeability, water-vapour resistance, thermal resistance, thermal absorptivity and areal density of knitted fabrics. Design/methodology/approach Weft knitted fabrics of various compositions were investigated. UPF was tested using the Labsphere UV transmittance analyser. The FX 3300 (Textest instruments) air permeability tester was used to test air permeability. Thermal comfort and water-vapour resistance were evaluated using the Alambeta and Permetest instruments, respectively. Based on image processing, the porosity was measured. Fabrics thickness and areal density were measured according to standard methods. Furthermore, parametric and non-parametric statistical test methods were applied to the data for analysis. Findings Linear regression was substantiated by Kolmogorov-Smirnov test. Then multiple linear regression of porosity and thickness together on UPF and comfort parameters were visually depicted by virtue of 3D linear plots. Residual analysis with quantile-quantile and probability plots, advocated the tests using the Shapiro-Wilk test. The result was validated by comparison with experimental data tested. The samples gave satisfactory relative errors and were supported by the z-test method. All tests indicated failure to reject the null hypothesis. Originality/value The predictive models were embedded into an interactive computer program. Fabric thickness and porosity are the inputs needed to run the program. It will predict the optimum UPF, areal density and thermophysiological comfort parameters. In a nutshell, knitters may use the program to determine optimum structural parameters for diverse permutations of UPF and thermophysiological comfort parameters; scilicet high UV protection together with low thermal insulation combined with low water-vapour resistance and high air permeability.

Purpose Lightweight, open construction cotton knitted fabrics generally do not impart good protection from solar ultraviolet radiation (UVR). As lightweight 100% cotton single jersey is highly cherished for summerwear, it is sine qua non to understand the structural parameters that effectively strike a good balance between UV protection and thermophysiological comfort of the wearer. Relatively heavy fabrics protect from UVR, but comfort is compromised because of waning porosity, increase in thickness and thermal insulation. The purpose of this paper is to engineer knits that will bestow maximum UV protection while preserving the thermophysiological comfort of the wearer. Design/methodology/approach In total, 27 cotton single jersey fabrics with different areal densities and yarn counts were selected. Ultraviolet protection factor (UPF) was calculated based on the work of Imrith (2022). To précis, the authors constructed a UV box to measure the UPF of fabrics, denoted as UPFB. UPFB data were correlated with AATCC 183-2004 and yielded high correlation, R2 0.977. It was concluded that UPF 50 corresponds to UPFB 94.3. Thermal comfort properties were measured on the Alambeta and water-vapour resistance on the Permetest. Linear programming (LP) was used to optimize UPFB and comfort. Linear optimization focused on maximizing UPFB while keeping the thermophysiological comfort and areal density as constraints. Findings The resulting linear geometrical and sensitivity analyses generated multiple technically feasible solutions of fabrics thickness and porosity that gave valid UPFB, thermal absorptivity and water-vapour and thermal resistance. Subsequently, an interactive optimization software was developed to predict the stitch length, tightness factor and yarn count for optimum UPFB from a given areal density. The predicted values were then used to knit seven 100% cotton single jersey fabrics and were tested for UV protection. All seven fabrics gave UPFB above the threshold, that is, higher than 94.3. The mathematical model demonstrated good correlations with the optimized parameters and experimental values. Originality/value The optimization software predicted the optimum UPFB reasonably well, starting from the fabric structural and constructional parameters. In addition, the models were developed as interactive user interfaces, which can be used by knitted fabric developers to engineer cotton knits for maximizing UV protection without compromising thermophysiological comfort. It has been demonstrated that LP is an efficient tool for the optimization and prediction of targeted knitted fabrics parameters.

No abstract