No abstract

The present work is a part of a comprehensive program that aims to evaluate the girth welding procedures for heavy wall API 5L X65 pipes produced for sour service applications. This article describes the results of toughness, strength and sour resistance of girth welds produced with different welding consumables. The methodology applied included girth welds production with GTAW process for root pass using ER70S-6 consumable and FCAW process for filling passes using E71T-1CJ and E91T1-GM-H4 consumables. Mechanical tests of Charpy, CTOD, tensile, hardness and stress corrosion cracking were also performed. The E71T-1CJ resulted in a girth weld with tensile and yield strength around 7% lower than the pipe. However, according to the papers analyzed at this study, a value up to 10% of undermatching could be acceptable. The CTOD and Charpy tests showed good toughness and weld metal embrittlement was not observed. The hardness and the stress corrosion cracking tests demonstrated that the consumable ER70S-6 is suitable for sour service. All properties evaluated met the requirements specified by the onshore pipeline standards, showing that the consumables ER70S-6, E71T-1CJ and E91T1-GM-H4 are suitable for the welding of heavy wall X65 pipe with sour service and toughness requirements. If an overmatching is required, the E91T1-GM-H4 shall be used to assure a strength overmatching and prevent plastic strain concentration at the weld metal. The results provided by this paper can be used for consumable selection and for welding procedure qualification of pipelines construction when heavy wall API 5L X65 are used for sour gas transportation.

ResumoEste trabalho analisa a tenacidade e dureza do metal de solda e ZAC da solda circunferencial de tubos X65, X70 e X80 para serviço ácido. Os tubos de elevada resistência, fabricados para serviço ácido, apresentam grande desafio para a soldagem. Os consumíveis e processos devem ser capazes de produzir uma junta soldada de alta resistência, baixa dureza e elevada tenacidade. O objetivo deste estudo foi identificar problemas de amolecimento ou fragilização da ZAC e verificar se a elevada resistência não prejudica a tenacidade e dureza do metal de solda. A metodologia incluiu a soldagem circunferencial e ensaios de dureza e CTOD. Os resultados mostraram que o metal de solda e a ZAC do X65 e X70, são adequadas para o emprego em dutos terrestres. Observou-se um amolecimento na ZAC do X70 e X80 que, de acordo com a literatura, não é crítico para projetos baseados em tensão. Para o X80, o CTOD da ZAC ficou abaixo do valor mínimo desejado, indicando que pode ter ocorrido a formação de zonas frágeis localizadas e resultando na necessidade de estudos complementares para ajustar os parâmetros de soldagem. Os resultados deste estudo servem como base para uma futura aplicação destes materiais em campo. Palavras-chave: Soldagem circunferencial; X70; X80; Serviço ácido. EFFECT OF GIRTH WELDING AT THE WELD METAL AND HAZ OF X65MS, X70MS AND X80MS PIPES AbstractThis paper analyses the HAZ and weld metal toughness and hardness of sour service X65, X70 and X80 girth welds. The high strength steel pipes produced for sour service introduce a big challenge for welding. The process and consumables applied should be able to produce a high strength, high toughness and low hardness welded joint. The purpose of this study was identify HAZ softening and embrittlement and whether the high strength does not affect the weld metal hardness and toughness. The methodology includes pipe girth welding, CTOD and hardness tests. Results showed that HAZ and weld metal of X65 and X70 pipes are suitable for pipelines. The X70 and X80 HAZ presented softening that, according to the literature, is not a critical point for stress based design. The X80 HAZ presented CTOD below the desired value. It indicates that local brittles zones could be present and new tests should be done in order to define better welding parameters.