We performed a systematic investigation of mechanical compaction, strain localization, and permeability in Leitha limestone. This carbonate from the area of Vienna (Austria) occurs with a broad range of grain sizes and porosity, due to changes in depositional regime and degree of cementation. Our new mechanical data revealed a simple relation between porosity and mechanical strength in both the brittle and ductile regimes. Increasing cementation and decreasing porosity led to a significant increase of the rock strength in both regimes. Micromechanical modeling showed that the dominant micromechanisms of inelastic deformation in Leitha limestone are pore‐emanated microcracking in the brittle regime, and grain crushing and cataclastic pore collapse in the ductile regime. Microstructural analysis and X‐ray computed tomography revealed the development of compaction bands in some of the less cemented samples, while more cemented end‐members failed by cataclastic flow in the compactant regime. In contrast to mechanical strength, permeability of Leitha limestone was not significantly impacted by increasing cementation and decreasing porosity. Our microstructural and tomography data showed that this was essentially due to the existence of a backbone of connected large macropores in all our samples, which also explained the relatively high permeability (in the range of 2–5 darcies) of Leitha limestone in comparison to other carbonates with significant proportion of micropores.

We examined cataclastic shear bands (CSB) with varying degrees of deformation and alteration that formed in uncemented, arkosic sediments under identical kinematic conditions. The investigated outcrop in eastern Austria exposes numerous closely spaced sets of CSB formed at low burial depth. The uncemented host sediment consists of detrital quartz, albite, micas, and metamorphic lithoclasts. We distinguished three types of CSB, which differ in macroscopic and microscopic properties as well as in influence on fluid flow (i.e., single bands, multistrand bands, and band clusters). All band types show preferred fracturing of sericited albite grains and decomposition of biotite through mechanical deformation and subsequent chemical alteration. These mechanisms reduce the mean grain size, increase the amount of phyllosilicates in the matrix, and facilitate later growth of authigenic clay minerals. The dominant deformation mechanisms and influence on fluid flow are controlled by the initial composition and intensity of diagenetic alteration. We identified different evolutionary stages from a high-porosity host rock (porosity ½Φ = 35%) to a deformation band cluster (Φ = 6%) that acts as fluid baffle. The measured reduction in porosity of up to 29% is reflected by retention of fluids along band clusters, along multistrand bands, and between intersecting bands. The timing and direction of the specific fluid flows can be determined by the interaction with the deformation bands. These findings suggest that localized

The present study examines deformation bands in calcareous arkosic sands. The investigated units can be considered as an equivalent to the Matzen field in the Vienna Basin (Austria), which is one of the most productive oil reservoirs in central Europe. The outcrop exposes carbonate-free and carbonatic sediments of Badenian age separated by a normal fault. Carbonatic sediments in the hanging wall of the normal fault develop dilation bands with minor shear displacements (< 2 mm), whereas carbonate-free sediments in the footwall develop cataclastic shear bands with up to 70 cm displacement. The cataclastic shear bands show a permeability reduction up to 3 orders of magnitude and strong baffling effects in the vadose zone. Carbonatic dilation bands show a permeability reduction of 1-2 orders of magnitude and no baffling structures. We distinguished two types of deformation bands in the carbonatic units, which differ in deformation mechanisms, distribution and composition. Full-cemented bands form as dilation bands with an intense synkinematic calcite cementation, whereas the younger loose-cemented bands are dilatant shear bands cemented by patchy calcite and clay minerals. All analyzed bands are characterized by a porosity and permeability reduction caused by grain fracturing and cementation. The changed petrophysical properties and especially the porosity evolution are closely related to diagenetic processes driven by varying pore fluids in different diagenetic environments. The deformation band evolution and sealing capacity is controlled by the initial host rock composition.