A crucial problem in the development of new hydrogen technologies is the need for lightweight and safe storage of acceptable amounts of hydrogen, in particular for portable or mobile applications. A new and innovative technology based on capillary arrays has been developed. These systems ensure the safe infusion, storage, and controlled release of hydrogen gas, even when storage pressures of up to 1200 bar are applied. This technology enables the storage of a significantly higher amount of hydrogen than other approaches. It has already surpassed the US Department of Energy's 2010 target, and is expected to meet the DOE's 2015 target in the near future. The main determinant in this storage technology is the pressure resistance of glass capillaries. It is well known that quartz, for example, is three times stronger than steel. At the same time, the density is about three times lower which means that much less material is necessary to reach the same pressure resistance. The pressure resistance of single capillaries has been determined in relation to various capillary materials and dimensions, wall thicknesses etc. in order to find out optimal parameters for the “final” capillaries.

Rotor vibration attenuation is achieved with damping devices which work on different, often mutually coupled, physical principles. Squeeze film dampers are damping devices that have been widely used in rotordynamic applications. A new concept of a 5-segmented integral squeeze film damper, in which a flexure pivot tilting pad journal bearing is integrated, was investigated. The damper is studied for the eccentric position between the outer and inner ring of the squeeze film land. The ANSYS CFX software was used for solving the pressure and velocity distribution. The development of the complex three-dimensional computational fluid dynamics model of the squeeze film damper, learning more about the effect of the forces in the damper, and the knowledge about the behaviour of the flow are the principal contributions of this article.

The paper deals with the simulation of cooling processes of the aluminium profiles inside the water quench. Cooling of profile surfaces is performed by water spray, which is created by mixing a water and an air in a nozzles. Formulas were found in literature, modified and applied to a given problem that significantly simplified a solution. The task of numerical simulations was to determine temperature and velocity profile on aluminium profile surfaces for establishing of the heat transfer coefficient which was used as the convective boundary condition necessary to solve the heat transfer in the aluminium profile by finite element method. The difference between FEM and CFD results is up to 10%.

The energy efficiency of machines is nowadays an intensively studied problem. The efficiency of the induction motor is dominantly influenced by the rotor’s and stator winding’s temperature. The main goal of the research presented in this paper is to develop a methodology based on Computational Fluid Dynamics (CFD) analysis of internal and external aerodynamics, which is necessary for the optimisation of cooling of the induction motors. In this paper, the theoretical, as well as the numerical study of the internal and external aerodynamics of the induction motor, is described and verified by the experimental measurements. In the CFD-based numerical study, the Reynolds-averaged Navier–Stokes (RANS) turbulence modelling approach was applied to the flow field simulations inside and outside the induction motor. The complexity of the solved problem is increased not only by the geometric asymmetry but also by the flow’s asymmetric character caused by the fan’s rotation to cool the motor casing. This increases demand, especially on computational resources, as it is impossible to create a simplified numerical model incorporating symmetry. The volume flow of the cooling air and velocity between ribs was measured for the experimental study. Comparing the results of the Computational Fluid Dynamics (CFD) simulations and data obtained from the experimental measurement, we concluded that the results of CFD simulations are in good relationship with the results of experimental measurement and analytical approximations. An experimentally validated CFD model of the induction motor, the so-called digital twin, will be in the future used for virtual optimisation of the new designs concerning minimising losses and maximising efficiency, respectively.

The work deals with possibilities of using this specific material. It is focused on cast metal foams with a regular arrangement of internal cells and it refers to already used casting technologies -the production of metal foamswith the aid of sand cores. Metal foamsare used in many industries, such as: automotive, aerospace, construction, power engineering. They have unique propertiesand due to lower weight with sufficient strength and greater contact surface can be used, for example, for the conduction of heat. This article deals with the useof the metal foam as a heat exchanger. The efficiency of the heat exchanger depends on its shape and size and therefore the study is focused first on the optimization of the shape before the proper manufacture.