Polymerase chain reaction (PCR) is recognized as a rapid, sensitive, and specific molecular diagnostic tool for the analysis of nucleic acids. However, the sensitivity and kinetics of diagnostic PCR may be dramatically reduced when applied directly to biological samples, such as blood and feces, owing to PCR-inhibitory components. As a result, pre-PCR processing procedures have been developed to remove or reduce the effects of PCR inhibitors. Pre-PCR processing comprises all steps prior to the detection of PCR products, that is, sampling, sample preparation, and deoxyribonucleic acid (DNA) amplification. The aim of pre-PCR processing is to convert a complex biological sample with its target nucleic acids/cells into PCR-amplifiable samples by combining sample preparation and amplification conditions. Several different pre-PCR processing strategies are used: (1) optimization of the DNA amplification conditions by the use of alternative DNA polymerases and/or amplification facilitators, (2) optimization of the sample preparation method, (3) optimization of the sampling method, and (4) combinations of the different strategies. This review describes different pre-PCR processing strategies to circumvent PCR inhibition to allow accurate and precise DNA amplification.
These data demonstrate the clinical potential of covalently bound VAN and CAS on Ti to reduce microbial biofilm formation without jeopardizing osseointegration.
INTRODUCTIONThe use of conventional and real-time PCR is to some extent restricted by the presence of PCR inhibitors. This is particularly so when the techniques are applied directly to complex biological samples such as clinical, environmental, or food samples for the detection of microorganisms. PCR inhibitors can originate from the sample itself, or as a result of the method used to collect or otherwise prepare the sample. Either way, inhibitors can dramatically reduce the sensitivity and amplification efficiency of PCR. This article discusses methods of reducing inhibition and designing reliable and sensitive conventional and real-time PCR experiments.
A quantitative reverse transcription-PCR (qRT-PCR) method was developed to monitor the relative expression of the type B botulinum neurotoxin (BoNT/B) gene (cntB) in Clostridium botulinum. The levels of cntB mRNA in five type B strains were accurately monitored by using primers specific for cntB and for the reference gene encoding the 16S rRNA. The patterns and relative expression of cntB were different in the different strains. Except for one of the strains investigated, an increase in cntB expression was observed when the bacteria entered the early stationary growth phase. In the proteolytic strain C. botulinum ATCC 7949, the level of cntB mRNA was four-to fivefold higher than the corresponding levels in the other strains. This was confirmed when we quantified the production of extracellular BoNT/B by an enzyme-linked immunosorbent assay and measured the toxicity of BoNT/B by a mouse bioassay. When the effect of exposure to air on cntB expression was investigated, no decline in the relative expression was observed in spite of an 83% reduction in the viable count based on the initial cell number. Instead, the level of cntB mRNA remained the same. When there was an increase in the sodium nitrite concentration, the bacteria needed a longer adjustment time in the medium before exponential growth occurred. In addition, there was a reduction in the expression of cntB compared to the expression of the 16S rRNA gene at higher sodium nitrite concentrations. This was most obvious in the late exponential growth phase, but at the highest sodium nitrite concentration investigated, 45 ppm, a one-to threefold decline in the cntB mRNA level was observed in all growth phases.
Biofilm-associated infections, particularly those caused by Staphylococcus aureus, are a major cause of implant failure. Covalent coupling of broad-spectrum antimicrobials to implants is a promising approach to reduce the risk of infections. In this study, we developed titanium substrates on which the recently discovered antibacterial agent SPI031, a N-alkylated 3, 6-dihalogenocarbazol 1-(sec-butylamino)-3-(3,6-dichloro-9H-carbazol-9-yl)propan-2-ol, was covalently linked (SPI031-Ti). We found that SPI031-Ti substrates prevent biofilm formation of S. aureus and Pseudomonas aeruginosa in vitro, as quantified by plate counting and fluorescence microscopy. To test the effectiveness of SPI031-Ti substrates in vivo, we used an adapted in vivo biomaterial-associated infection model in mice in which SPI031-Ti substrates were implanted subcutaneously and subsequently inoculated with S. aureus. Using this model, we found a significant reduction in biofilm formation (up to 98%) on SPI031-Ti substrates compared to control substrates. Finally, we demonstrated that the functionalization of the titanium surfaces with SPI031 did not influence the adhesion and proliferation of human cells important for osseointegration and bone repair. In conclusion, these data demonstrate the clinical potential of SPI031 to be used as an antibacterial coating for implants, thereby reducing the incidence of implant-associated infections. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:2191-2198, 2016.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.