Radioactive counterions were used to track the ratio of positive to negative polymer repeat units within a polyelectrolyte multilayer made from poly(diallyldimethylammonium chloride), PDADMAC, and poly(styrene sulfonate), PSS. For this widely employed pair of "linearly" assembled polyelectrolytes it was found that the accepted model of charge overcompensation for each layer is incorrect. In fact, overcompensation at the surface occurs only on the addition of the polycation, whereas PSS merely compensates the PDADMAC. After the assembly of about a dozen layers, excess positive sites begin to accrue in the multilayer. Treating the surface as a reaction-diffusion region for pairing of polymer charges, a model profile was constructed. It is shown that different reaction-diffusion ranges of positive and negative polyelectrolyte charge lead to a blanket of glassy, stoichiometric complex growing on top of a layer of rubbery, PDADMAC-rich complex. Though overcompensation and growth was highly asymmetric with respect to the layer number, entirely conventional "linear" assembly of the multilayer was observed. The impact of asymmetric growth on various properties of multilayers is discussed.

Sulfonation of narrow polydispersity polystyrene, PS, standards remains the method of choice for generating polystyrene sulfonate, PSS, samples with defined composition. Although a variety of sulfonation techniques have been described, relatively little is reported on the material obtained, which is used for so many studies on the fundamental behavior of polyelectrolytes. Here, we show that powdered polystyrene treated with concentrated sulfuric acid (96%) at 90 °C without catalyst yields fully sulfonated PSS. Extensive characterization with 1H and 13C NMR as well as size exclusion chromatography coupled with static and dynamic light scattering shows no evidence of sulfone crosslinking or chain degradation under the conditions used. Though mono‐sulfonated as soon as it dissolves in the acid, the PSS contains about 6% meta substitution. Sulfonation kinetics for this heterogeneous reaction depend strongly on particle size, sulfuric acid content and temperature. For preparing perdeuterated PSS from the corresponding PS it is essential to employ D2SO4, as about half of the aromatic units undergo H/D exchange during sulfonation. The remaining ortho H/D may be exchanged with extended exposure to the concentrated sulfuric acid, but the meta site is deactivated. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2416–2624

Stoichiometric polyelectrolyte complexes, PECs, from fully sulfonated poly(styrenesulfonate), PSS, as polyanion and poly(diallyldimethylammonium chloride), PDADMA, as polycation, were prepared by mixing them at optimized polyelectrolyte and NaCl concentrations. The complexes were compacted by ultracentrifugtion and then annealed in NaCl solutions at elevated temperatures to allow the polymers to fully intermix and relax. Small-angle neutron scattering, SANS, with contrast matching, was used to study single polyelectrolyte chain dimensions in PECs made from a mixture of deuterated and protonated PSS chains. Two PSS molecular weights in PECs were investigated at various ionic strengths. SANS curves, form factor fits, and corresponding Kratky plots indicate the Gaussian nature of the polyelectrolyte chains in the complexes regardless of molecular weight. PSS coils were slightly larger than the unperturbed dimension, more so for the higher molecular weight material, which was attributed to an effective stiffening of the chain due to ladderlike interactions between polyelectrolytes.

Atomic hydrogen electrosorption is reported at crystallite sites of polyacrylate-capped Pt nanoparticles (d = 2.5 +/- 0.6 nm), by assembling nanostructured electrodes of polyacrylate-Pt nanocrystallites layer-by-layer in a cationic polyelectrolyte, poly(diallyldimethylammonium chloride). Cyclic voltammetry in 1 M H2SO4 revealed a strongly adsorbed hydrogen state and a weakly adsorbed hydrogen state assigned to adsorption at (100) and (110) sites of the modified nanocrystallites, respectively. Resolving hydrogen adsorption states signifies that surface capping by the carboxylate groups is not irreversibly blocking hydrogen adsorption sites at the modified Pt nanoparticle surface. Adsorption peak currents increased with increasing the number of layers up to 16 bilayers, indicating the feasibility of nanoparticle charging via interparticle charge hopping and the accessibility of adsorption states within the thickness of the nanoparticle/polyelectrolyte multilayers. Despite similarity in hydrogen adsorption in the cyclic voltammorgrams in 1 M H2SO4, negative shifts in adsorption potentials were measured at the nanocrystallite Pt-polyelectrolyte multilayers relative to a polycrystalline bulk Pt surface. This potential shift is attributed to a kinetic limitation in the reductive hydrogen adsorption as a result of the Pt nanoparticle surface modification and the polyelectrolyte environment.

Homopolynucleotides--poly(adenylic acid), poly(A), and poly(uridylic acid), poly(U)--were assembled, layer-by-layer, into thin films with poly(ethylenimine), PEI. Various combinations and sequences of polynucleotide and PEI were used to highlight contributions of electrostatic versus hydrogen bonding as driving forces for multilayer build-up. Assembly of alternating poly(A) and poly(U) failed to yield growing films, due to excessively strong interactions between these complimentary strands. The surface morphology of multilayers depended on the deposition order and whether films had been annealed by salt. Films assembled from preformed A/U duplexes (having high persistence lengths) were very smooth. Individual adsorption steps, followed by optical waveguide light-mode spectroscopy, showed that only complementary polynucleotides adsorb by H-bonding to the surface of a growing multilayer. In contrast to behavior usually observed for polyelectrolyte multilayer build-up, the films decreased in thickness with increasing salt concentration.