No abstract

Copper hexacyanoferrate, Cu(II)[Fe(III)(CN)6]2/3·nH2O, was synthesized, and varied amounts of K(+) ions were inserted via reduction by K2S2O3 (aq). Ideally, the reaction can be written as Cu(II)[Fe(III)(CN)6]2/3·nH2O + 2x/3K(+) + 2x/3e(-) ↔ K2x/3Cu(II)[Fe(II)xFe(III)1-x(CN)6]2/3·nH2O. Infrared, Raman, and Mössbauer spectroscopy studies show that Fe(III) is continuously reduced to Fe(II) with increasing x, accompanied by a decrease of the a-axis of the cubic Fm3̅m unit cell. Elemental analysis of K by inductively coupled plasma shows that the insertion only begins when a significant fraction, ∼20% of the Fe(III), has already been reduced. Thermogravimetric analysis shows a fast exchange of water with ambient atmosphere and a total weight loss of ∼26 wt % upon heating to 180 °C, above which the structure starts to decompose. The crystal structures of Cu(II)[Fe(III)(CN)6]2/3·nH2O and K2/3Cu[Fe(CN)6]2/3·nH2O were refined using synchrotron X-ray powder diffraction data. In both, one-third of the Fe(CN)6 groups are vacant, and the octahedron around Cu(II) is completed by water molecules. In the two structures, difference Fourier maps reveal three additional zeolitic water sites (8c, 32f, and 48g) in the center of the cavities formed by the -Cu-N-C-Fe- framework. The K-containing compound shows an increased electron density at two of these sites (32f and 48g), indicating them to be the preferred positions for the K(+) ions.

We have investigated the properties of the electrode/electrolyte interfaces of composite electrodes based on nanostructured iron oxide cycled in Li-and Na-half cells containing analogous electrolytes (i.e., LiClO 4 or NaClO 4 in ethylene carbonate:diethyl carbonate (EC:DEC)). A meticulous nondestructive step-by-step analysis of the first discharge/charge cycle has been conducted via soft X-ray photoelectron spectroscopy using synchrotron radiation. In this way, different depths were probed by varying the photon energy (hν) for both electrochemical systems. The results of this thorough study clearly highlight the differences and the similarities of their respective solid electrolyte interface (SEI) layers in terms of formation, composition, structure, or thickness, as well as their conversion mechanisms. We specifically point out that the SEI coverage is more pronounced, and a homogeneous distribution rich in inorganic species exists in the case of Na, compared to the organic/inorganic layered structure observed for the Li system. The SEI formation gradually occurs during the first discharge in both Li-and Na-half cells. For Na, a predeposit layer is formed directly by simple contact of the electrode with the electrolyte. Despite using similar electrolytes, the nature of the cation (Li + or Na + ) has significant impact on the overall composition/structure of the resulting SEI.

The cathode material P2-Nax Co2/3 Mn2/9 Ni1/9 O2, which could be used in Na-ion batteries, was investigated through synchrotron-based hard X-ray photoelectron spectroscopy (HAXPES). Nondestructive analysis was made through the electrode/electrolyte interface of the first electrochemical cycle to ensure access to information not only on the active material, but also on the passivation layer formed at the electrode surface and referred to as the solid permeable interface (SPI). This investigation clearly shows the role of the SPI and the complexity of the redox reactions. Cobalt, nickel, and manganese are all electrochemically active upon cycling between 4.5 and 2.0 V; all are in the 4+ state at the end of charging. Reduction to Co(3+), Ni(3+), and Mn(3+) occurs upon discharging and, at low potential, there is partial reversible reduction to Co(2+) and Ni(2+). A thin layer of Na2 CO3 and NaF covers the pristine electrode and reversible dissolution/reformation of these compounds is observed during the first cycle. The salt degradation products in the SPI show a dependence on potential. Phosphates mainly form at the end of the charging cycle (4.5 V), whereas fluorophosphates are produced at the end of discharging (2.0 V).

Water‐splitting photoanodes based on semiconductor materials typically require a dopant in the structure and co‐catalysts on the surface to overcome the problems of charge recombination and high catalytic barrier. Unlike these conventional strategies, a simple treatment is reported that involves soaking a sample of pristine BiVO4 in a borate buffer solution. This modifies the catalytic local environment of BiVO4 by the introduction of a borate moiety at the molecular level. The self‐anchored borate plays the role of a passivator in reducing the surface charge recombination as well as that of a ligand in modifying the catalytic site to facilitate faster water oxidation. The modified BiVO4 photoanode, without typical doping or catalyst modification, achieved a photocurrent density of 3.5 mA cm−2 at 1.23 V and a cathodically shifted onset potential of 250 mV. This work provides an extremely simple method to improve the intrinsic photoelectrochemical performance of BiVO4 photoanodes.