The presence of a conducting metal surface is known to affect the emission of a fluorophore in its proximity. This can lead to an enhancement in its fluorescence intensity along with a decrease in the fluorescence lifetime. This phenomenon, sometimes known as metal enhanced fluorescence, has implications in the area of sensing and "lab on a chip" applications. Here controlled, localised use of metallic structures can be advantageous in enhancing the detection of a fluorescent signal. The sol-gel technique has been demonstrated as a useful method by which to produce a biocompatible material. The versatility of the reaction allows for the inclusion of metal ions, which can form metallic nanostructures permitting the potential enhancement of fluorescence to be exhibited. In this work we incorporate silver nitrate within silica sol-gel derived films produced using a simple procedure at relative low temperatures (close to ambient). A compact time-resolved fluorescence microscope equipped with a semiconductor laser was used to photoactivate the silver ions to form localised metallic structures within the films. Patterning was achieved by computer control of the microscope stage and using the laser in CW mode. The films were characterised using AFM and UV-vis spectroscopy to ascertain the presence of the photoactivated silver nanostructures. The effect of the presence of these structures was elucidated by studying the time-resolved fluorescence of FITC labelled bovine serum albumin adsorbed to the films, where a decrease in the lifetime of the FITC label was observed in the location of the nanostructures.

The efficiency of Förster resonance energy transfer (FRET) can be enhanced in the presence of a metal. Herein, we demonstrate the increased efficiency for a novel model sensor system where FRET is shown to occur between Rhodamine 6G in the bulk sol-gel matrix and Texas Red, which is held a fixed distance away by covalent attachment onto a silane spacer. Silver colloids are formed using light to initiate the reduction of a silver salt, which can be achieved at controlled locations within the film. Both the fluorescence intensity and lifetime maps and analysis indicate that an enhanced FRET efficiency has been achieved in the presence of silver nanoparticles. An increase in efficiency of 1.2-1.5 times is demonstrated depending on the spacer used. The novelty of our approach lies in the method of silver-nanoparticle formation, which allows for the accurate positioning of the silver nanoparticles and hence selective fluorescence enhancement within a biocompatible host material. Our work gives a practical demonstration of metal-enhanced FRET and demonstrates the ability of such systems to be developed for molecular-recognition applications that could find use in lab-on-a-chip technologies.

Simple to manufacture polysaccharide films containing a silver salt, from which silver nanostructures can be produced in situ by light irradiation, were investigated for possible biosensing applications. The silver nanostructures were patterned in situ within a film and cast from a liquid solution of gellan gum, using a compact time-resolved fluorescence microscope. The position and time of irradiation, made using a semiconductor laser in CW mode, were computer controlled. Evidence for their formation was obtained via UV-vis spectroscopy, AFM and SEM-EDAX. On drying the polysaccharide film exhibited a viscosity increase of several orders of magnitude, which was elucidated by changes in the fluorescence lifetime of a probe molecule (DASPMI). To demonstrate the potential for biocompatible sensing applications the influence of the presence of areas of silver nanostructures on the fluorescence of a protein (bovine serum albumin) labelled with fluorescein isothiocyanate was monitored via fluorescence lifetime imaging and the photophysical behaviour found to be consistent with a metal induced increase in the radiative decay rate.

Fluorescence microscopy provides a non-invasive means for visualising dynamic protein interactions. As well as allowing the calculation of kinetic processes via the use of time-resolved fluorescence, localisation of the protein within cells or model systems can be monitored. These fluorescence lifetime images (FLIM) have become the preferred technique for elucidating protein dynamics due to the fact that the fluorescence lifetime is an absolute measure, in the main independent of fluorophore concentration and intensity fluctuations caused by factors such as photobleaching. In this work we demonstrate the use of a time-resolved fluorescence microscopy, employing a high repetition rate laser excitation source applied to study the influence of a metal surface on fluorescence tagged protein and to elucidate viscosity using the fluorescence lifetime probe DASPMI. These were studied in a cellular environment (yeast) and in a model system based on a sol-gel derived material, in which silver nanostructures were formed in situ using irradiation from a semiconductor laser in CW mode incorporated on a compact time-resolved fluorescence microscope (HORIBA Scientific DeltaDiode and DynaMyc).