© 2015 The Authors. Published by Elsevier Ltd.The research and development of nanocellulose-reinforced polymer composites have dramatically increased in recent years due to the possibility of exploiting the high tensile stiffness and strength of nanocellulose. In the work, the environmental impact of bacterial cellulose (BC)- and nanofibrillated cellulose (NFC)-reinforced epoxy composites were evaluated using life cycle assessment (LCA). Neat polylactide (PLA) and 30 wt.-% randomly oriented glass fibre-reinforced polypropylene (GF/PP) composites were used as benchmark materials for comparison. Our cradle-to-gate LCA showed that BC- and NFC-reinforced epoxy composites have higher global warming potential (GWP) and abiotic depletion potential of fossil fuels (ADf) compared to neat PLA and GF/PP even though the specific tensile moduli of the nanocellulose-reinforced epoxy composites were higher than neat PLA and GF/PP. However, when the use phase and the end-of-life of nanocellulose-reinforced epoxy composites were considered, the green credentials of nanocellulose-reinforced epoxy composites were comparable to that of neat PLA and GF/PP composites. Our life cycle scenario analysis further showed that the cradle-to-grave GWP and ADf of BC- and NFC-reinforced epoxy composites could be lower than neat PLA when the composites contains more than 60 vol.-% nanocellulose. This suggests that nanocellulose-reinforced epoxy composites with high nanocellulose loading is desirable to produce materials with greener credentials than the best performing commercially available bio-derived polymers

Miniaturised test specimens are often used for the tensile testing of cellulose nanopapers as there are currently no standardised test geometries to evaluate their tensile properties. In this work, we report the influence of test specimen geometries on the measured tensile properties of plant-derived cellulose nanofibres (CNF) and microbially synthesised bacterial cellulose (BC) nanopapers. Four test specimen geometries were studied: (i) miniaturised dog bone specimen with 2 mm width, (ii) miniaturised rectangular specimen with 5 mm width, (iii) standard dog bone specimen with 5 mm width and (iv) standard rectangular specimen with 15 mm width. It was found that the tensile moduli of both CNF and BC nanopapers were not significantly influenced by the test specimen geometries if an independent strain measurement system (video extensometer) was employed. The average tensile strength of the cellulose nanopapers is also influenced by test specimen geometries. It was observed that the smaller the test specimen width, the higher the average tensile strength of the cellulose nanopapers. This can be described by the weakest link theory, whereby the probability of defects present in the cellulose nanopapers increases with increasing test specimen width. The Poisson's ratio and fracture resistance of CNF and BC nanopapers are also discussed

Cellulose nanopapers have gained significant attention in recent years as large-scale reinforcement for high-loading cellulose nanocomposites, substrates for printed electronics and filter nanopapers for water treatment. The mechanical properties of nanopapers are of fundamental importance for all these applications. Cellulose nanopapers can simply be prepared by filtering a suspension of nanocellulose, followed by heat consolidation. It was already demonstrated that the mechanical properties of cellulose nanopapers can be tailored by the fineness of the fibrils used or by modifying nanocellulose fibrils for instance by polymer adsorption, but nanocellulose blends remain underexplored. In this work, we show that the mechanical and physical properties of cellulose nanopapers can be tuned by creating nanopapers from blends of various grades of nanocellulose, i.e. (mechanically refined) bacterial cellulose or cellulose nanofibrils extracted from never-dried bleached softwood pulp by chemical and mechanical pre-treatments. We found that nanopapers made from blends of two or three nanocellulose grades show synergistic effects resulting in improved stiffness, strength, ductility, toughness and physical properties.This article is part of a discussion meeting issue 'New horizons for cellulose nanotechnology'.

No abstract

In this study, we investigated the mechanical response of polylactide (PLLA) reinforced with multiple layers of BC nanopaper. Laminated composites consisting of 1, 3, 6 and 12 sheet(s) of BC nanopaper were produced. It was observed that increasing the number of BC nanopaper led to an increase in the porosity of the resulting BC nanopaper-reinforced PLLA laminated composites. The tensile moduli of the laminated composites were found to be ~12.5-13.5 GPa, insensitive to the number of sheets of BC nanopaper in the composites. However, the tensile strength of the laminated composites decreased by up to 25% (from 121 MPa to 95 MPa) when the number of reinforcing BC nanopaper sheets increased from 1 to 12 sheets. This was attributed to the presence and severity of the scale-induced defects increased with increasing BC nanopaper sheets in the PLLA laminated composites.