This paper deals with a research focused on utilization of microparticle and short-fiber filler based on cotton post-harvest line residues in an area of polymeric composites. Two different fractions of the biological filler (FCR—reinforced cotton filler) of 20 and 100 µm and the filler with short fibers of a length of 700 µm were used in the research. The aim of the research was to evaluate mechanical characteristics of composites and adhesive bonds for the purpose of gaining new pieces of knowledge which will be applicable in the area of material engineering and assessing application possibilities of residues coming into being from agricultural products processing. Mechanical properties of the composite material produced by a vacuum infusion and tested at temperatures 20, 40, and 60 °C and adhesive bonds which were exposed to a low-cyclic loading, i.e., 1000 cycles at 30% to 70% from reference value of the maximum strength, were evaluated. Composite systems with the FCR adjusted in 5% water solution of NaOH showed higher strength values on average compared to untreated FCR. Unsuitable size of the FCR led to a deterioration of the strength. The filler in the form of 700 FCR microfibers showed itself in a positive way to composite materials, and the particle in the form of 20 FCR did the same to adhesive bonds. Results of adhesive bond cyclic tests at higher stress values (70%) demonstrated viscoelastic behavior of the adhesive layer.

Energy recovery of lignocellulosic waste material in the form of liquid fractions can yield alcohol-based fuels such as bioethanol or biobutanol. This study examined biobutanol derived from lignocellulosic material that was then used as an additive for diesel engines. Biobutanol was used in fuel mixtures with fatty acid methyl ester (FAME) obtained by esterification of animal fat (also a waste material) in the amounts of 10%, 30%, and 50% butanol. 100% diesel and 100% FAME were used as reference fuels. The evaluation concerned the fuel's effect on the external speed characteristics, harmful exhaust emissions, and fuel consumption while using the Non-Road Steady Cycle test. When the percentage of butanol was increased, the torque and the power decreased and the brake specific fuel consumption increased. The main advantage of using biobutanol in fuel was its positive effect on reducing the fuel's viscosity.

The global concentration of greenhouse gasses in the atmosphere is increasing as well as the emissions of harmful pollutants. Utilization of liquid biofuels in combustion engines helps to reduce these negative effects. For diesel engines, the most common alternative fuels are based on vegetable oils. Blending neat vegetable oils with diesel and/or alcohol fuels is a simple way to make them suitable for diesel engines. In this study, coconut oil was used in ternary fuel blends with diesel and butanol. Coconut oil is a potentially usable source of renewable energy, especially in the Pacific, where it is a local product. Diesel fuel-coconut oil-butanol fuel blends were used in concentrations of 70%/20%/10% and 60%/20%/20%, and 100% diesel fuel was used as a reference. The effect of the fuel blends on the production of harmful emissions, engine smoke, performance parameters, fuel consumption and solid particles production was monitored during the measurement. The engine was kept at a constant speed during the measurement and the load was selected at 50%, 75% and 100%. From the results, it can be stated that in comparison with diesel fuel, specific fuel consumption increased with a positive effect on the reduction of engine smoke.

This contribution focuses on utilizing blended biofuels of rapeseed oil and methanol with diesel. Rapeseed is one of the most cultivated energy crops in Europe, and its purpose in the blends is to increase the bio-content in test fuels. The purpose of methanol in the blends is to increase bio-content and compensate for the higher viscosity of the rapeseed oil. As methanol is almost insoluble in diesel and rapeseed oil, iso-butanol is used as a co-solvent. The fuel blends were tested in volumetric concentrations of diesel/rapeseed oil/methanol/iso-butanol 60/30/5/5, 50/30/10/10, and 50/10/20/20. Diesel was used as a reference. The measurements were performed on a turbocharged diesel engine Zetor 1204, loaded using the power-takeoff shaft of the Zetor Forterra 8641 tractor. In this paper, the effect of the blended fuels on performance parameters, engine efficiency, production of soot particles, and regulated and unregulated emissions are monitored and analyzed. It was found that engine power decreased by up to 27%, efficiency decreased by up to 5.5% at full engine load, emissions of NOX increased by up to 21.9% at 50% engine load, and production of soot particles decreased; however, the mean size of the particles was smaller.

In this article, sample damage and wear of forced-in joints is presented, and their reliability evaluated. Compared were shafts without additional finish treatment, rolled shafts and those with a TiSiN coating. Tribological samples under investigation operated in rotational bending conditions. Recorded was the number of fatigue cycles at which damage might occur. Reliability indicators were plotted, which demonstrated that coated shafts are distinguished by the highest reliability and low damage intensity. Macroscopic observations of shaft surfaces demonstrated the traces of adhesive wear and, in the case of shafts without additional treatment and in the case of rolled shafts, fretting wear traces in the form of a ring comprising the entire shaft circumference. Microscopic observations showed numerous build-ups on the surface, microcracks, and the occurrence of wear products in the gap between the shaft and sleeve. The highest fatigue strength was demonstrated by shafts with a TiSiN coating. The shaft section change area was the place where fatigue wear occurred.