Formaldehyde is a toxic chemical commonly found in the environment. Owing to its increased usage, its incidence has also increased, and there is a need to determine the concentration of formaldehyde for the pollution control purposes. In general, spectrophotometric methods are easy to perform, low-cost, selective and sensitive, but every spectrophotometric method has its advantages and disadvantages, which are an important factor when selecting the method for determination of formaldehyde. Therefore, the aim of the research described in this paper was to compare the current spectrophotometric methods and to summarize their advantages and disadvantages.

This scientific study deals with investigation of the heat of combustion and effective heat of combustion of selected electrical cables. Two different electrical cables for rated voltage of 0.6/1 kV were investigated. Both cables were power three-core with cross-section area of each core of 1.5 mm2. The cores of both cables were made of a bar cooper wire. Insulations of conductors of both cables were made of silane cross-linked polyethylene without any inorganic filler, while the bedding and outer sheath were made of polyethylene-based copolymer (the beddings were filled with two fillers - aluminium hydroxide and calcium carbonate, while the outer sheath were filled only with aluminium hydroxide). Reaction to fire class of both cables was B2ca, s1, d0, a1. The main difference in the investigated cables was that the core of one of them was wrapped in a glass mica tape (this cable showed circuit integrity maintenance under fire conditions during 180 minutes). The heat of combustion and effective heat of combustion were determined by the oxygen bomb calorimeter according to the ISO 1716:2018 standard. The highest effective heat of combustion showed the insulation of wires (for both cables 42.47 ± 0.03 MJ/kg), lower value showed outer sheath (interval form13.61 to 15.26 MJ/kg) and the lowest value was determined for bedding (interval from 4.69 to 6.39 MJ/kg). The effective heath of combustion per unit of length of both investigated cables lies in the interval from 1.37 to 1.38 MJ/m. Therefore, there is no significant difference in effective heats of combustion of the electrical cables investigated.

The aim of the research described in this paper was to study the impact of the electrical cables slope on the flame out time and the flame spread rate. Measured cables were thermally loaded by methanol flame (diameter of the container was 106 mm) at seven different slopes with respect to the horizontal plane (the slopes were 0° – horizontal orientation, 15°, 30°, 45°, 60°, 75° and 90° - vertical orientation). The first tested electrical cable was a copper three-core power one resistant to the flame spread with circuit integrity of the cable system during 30 minutes under fire (cross-section of each core was 1.5 mm2). The second tested electrical cable was a copper two-core signal one resistant to the flame spread with circuit integrity of the cable system during 30 minutes under fire (cross-section of each core was 0.5 mm2). The first electrical cable did not show reaction to fire class. The reaction to fire class of the second tested cable was B2ca, s1, d1, a1. The obtained results proved that slope had virtually no impact on the flame out time and the flame spread over the tested cable surface (tested cables of all slopes stopped burning after 1 to 5 seconds after methanol flame burned out). Likewise, the flame spread was only negligibly beyond the border of flame action for each cable slope.

This study deals with the Fire Growth Rate Index (FIGRA) as a key fire characteristic of electrical cables (determined by a cone calorimeter) that allows to estimate their reaction to fire class. Three power (supply) electrical cables (reaction to fire class B2ca) were tested by a cone calorimeter using different heat fluxes of 20, 30, 40 a 50 kW·m−2. The cables were three-wire (cross-section of each wire was 1.5 mm2) with a nominal voltage of 0.6 kV (alternating current), resp. 1 kV (direct current). The cable sheaths were made of an ethylene copolymer filled with aluminum hydroxide. The beddings were made of an ethylene copolymer filled with a mixture of aluminum hydroxide and calcium carbonate. The conductor insulations of one electrical cable were made of crosslinked polyethylene and the conductor insulations of the other two electrical cables were made of an ethylene copolymer filled with aluminum hydroxide. FIGRA was determined per unit length and unit area of electrical cables. FIGRA increased with increasing heat flux. At a heat flux of 50 kW·m−2, all the electric cables examined showed a very similar FIGRA (from 0.19 to 0.21 kW·m−1·s−1 and 18.4 to 21.2 kW·m−1·s−1, respectively). Conversely, at a heat flux of 20 kW·m−2, the investigated cables showed greater FIGRA variance (in the range of 0.11 to 0.16 kW·m−1·s−1 or 10.8 to 16.2 kW·m−1·s−1).