The purpose of this study was to investigate the effect of previous phosphoric acid etching on the dentin bond strength of single-step self-etch adhesive systems. Facial surfaces of bovine teeth were wet ground with #600 SiC paper. Adhesives were applied with and without previous phosphoric acid etching, and light irradiated. Resin composite was bonded to the adherend surface, followed by light irradiation and storage in water at 37 degrees C. Four groups (n = 10) were made per adhesive system: with and without previous acid etching and with and without thermal cycling between 5 degrees C and 55 degrees C for 10,000 cycles. Specimens were tested in a shear mode at a crosshead speed of 1.0 mm/min. Two-way ANOVA and Tukey HSD test at a level of 0.05 were performed. The changes in dentin bond strengths were different among the adhesive systems tested. In all experimental conditions of this study, the dentin bond strength decreased or remained unchanged with previous acid etching. From the results of this study, previous acid etching might not be acceptable for increasing dentin bond strength of the single-step self-etch adhesive systems.

An attempt was made to study the effect of interfacial slippage on the filler reinforcement based on the boundary condition that the constituents of a particle‐filled composite can slip relative to each other, but no cavities are formed at the interfaces. The elastic field satisfying these conditions is derived using the linear theory of elasticity and the effective elastic moduli of the composite are calculated. The following assumptions are made: (1) Filler particles are spherical, (2) fillers are completely dispersed, and (3) the volume fraction of fillers is sufficiently small that the interaction among fillers may be neglected. The expression for the shear modulus of the composite μ**, which is derived here, is consistent with the viscosity of a suspension which has been derived by Oldroyd. Experiments who that the increase of Young's modulus by glass beads (GB) is lower in polystyrene (PS) than in epoxy resin (Ep). The reinforcement in Ep‐GB systems can be estimated by the well known formula derived assuming perfect adhesion. However, the reinforcement in PS‐GB systems is in rather good agreement with the formula derived here assuming interfacial slippage.

This study investigated the effect of phosphoric acid etching on the dentin bond strength of five single-step self-etch adhesive systems; Absolute, Clearfil tri-S Bond, Fluoro Bond Shake One, G-Bond and One-Up Bond F Plus. Bovine mandibular incisors were mounted in self-curing resin and the facial surfaces were wet ground with #600 SiC paper. Adhesives were applied on the prepared dentin surfaces with and without prior phosphoric acid etching and light irradiated. Resin composite was condensed into a mold (ø4x2 mm), light irradiated and stored in water at 37 degrees C. Four groups (n=10) were made per adhesive system: with and without prior acid etching and with and without thermal cycling between 5 degrees C and 55 degrees C for 10,000 cycles. The specimens were tested in a shear mode at a crosshead speed of 1.0 mm/minute. Two-way ANOVA, Student t-test and Tukey HSD test at a level of 0.05 were done. For specimens without prior acid etching, the mean bond strengths to bovine dentin ranged from 12.8 to 17.1 MPa and ranged from 6.7 to 13.3 MPa for specimens with prior acid etching after 24 hours storage in water. When the specimens were subjected to thermal cycling, the mean bond strengths ranged from 10.7 to 24.8 MPa for the specimens without prior acid etching and 4.6 to 13.9 MPa for the specimens with prior acid etching. The changes in dentin bond strength were different among the adhesive systems tested. Failure modes were commonly adhesive failure associated with mixed failure for specimens with prior acid etching. For specimens without prior acid etching, failures in composite and dentin were increased. From the results of this in vitro study, prior acid etching might be not acceptable for increasing the dentin bond strengths of single-step self-etch adhesive systems.