AlMg alloys close to ¢-Al 3 Mg 2 intermetallic phase were processed by neutral gas coverage melting process of pure elemental Al and Mg with the composition of Al40 mass% Mg. Mechanical milling was applied in order to convert the pre-alloyed ingots to nanocrystalline or amorphous alloy. X-ray diffraction and transmission electron microscopy (TEM) tests were carried out to investigate the formation of Al 3 Mg 2 single phase nanoparticle. Having prepared the single phase intermetallic, it was added to the pre-alloyed matrix powder of Al4.5 mass% Cu, in different contents. The effect of the reinforcing agent on the microhardness and wear behavior of the nanocopmosites were studied thoroughly with the aid of press-sinter methodology and quantitative data recorders via pin-on-disk wear test. The results of microhardness tests revealed that the hardness of nanocomposites is significantly improved with increasing reinforcement content with in the matrix. The coexisted wear mechanisms, mainly delamination and abrasive, of the consolidated nanocopmosites were investigated through scanning electron microscopy (SEM) and TEM observations.

A T-shaped microfluidic micro-mixer was designed to mix desired concentrations of two fluid streams and to prepare their homogenous mixture solution. A hydrostatic pressure gradient was induced in one of the branches of the system (mixing channel) by applying external electric field and generating electroosmotic flow in the two other branches of the system. The flow field and transferred mass into the mixing channel can be regulated by controlling the applied voltage of the system. In order to prepare more homogenous mixture solution, some obstacles were added to the mixing channel to induce perturbation in the flow field and enhance the mixing efficiency of the system. Numerical simulations were performed to show the correctness of the proposed mixing strategy and to investigate the influences of the applied voltage on the mixing efficiency and induced pressure flow in the mixing channel. A proposed design can be used as a guideline to control and enhance mixing efficiency, and consequently functionality, of different microfluidic devices.

AC electroporation of a single cell in a microchannel was numerically studied. A 15 μm diameter cell was considered in a microchannel 25 μm in height and the influences of AC electric pulse on its membrane were numerically investigated. The cell was assumed to be suspended between two electroporative electrodes embedded on the walls of a microchannel. An amplitude and a time span of applied electric pulse were chosen to be 80 kV/m and 10 μs, respectively. For different frequency values (50, 100, 200, and 500 kHz), simulations were performed to show how the cell membrane was electroporated and the creation of nanopores. Obtained numerical results show that the most and the largest nanopores are created around poles of cell (nearest points of cell membrane to the electrodes). The numerical simulations also demonstrate that increased frequency will slightly decrease electroporated area of the cell membrane; additionally, growth of the created nanopores will be stabilized. It has also been proven that size and number of the created nanopores will be decreased by moving from the poles to the equator of the cell. There is almost no nanopore created in the vicinity of the equator. Frequency affects the rate of generation of nanopores. In case of AC electroporation, creation of nanopores has two phases that periodically repeat over time. In each period, the pore density sharply increases and then becomes constant. Enhancement of the frequency will result in decrease in time span of the periods. In each period, size of the created nanopores sharply increases and then slightly decreases. However, until the AC electric pulse is present, overall trends of creation and development of nanopores will be ascending. Variation of the size and number of created nanopores can be explained by considering time variation of transmembrane potential (difference of electric potential on two sides of cell membrane) which is clear in the results presented in this study.

No abstract

The goal of this study is to model the effects of wind on Cylindrical Trough Collectors (CTCs). Two major areas are discussed in this paper: 1) heat losses due to wind flow over receiver pipe and 2) average forces applied on the collector's body. To accomplish these goals a 2D modeling of CTC was carried out using commercial codes with various wind velocities and collector orientations. Ambient temperature was assumed to be constant at 300 K and for specific geometries different meshing methods and boundary conditions were used in various runs. Validation was done by comparing the simulation results for a horizontal collector with empirical data. It was observed that maximum force of 509.1 Newton per Meter occurs at +60 degrees. Nusselt number is almost the constant for positive angles while at negative angles it varies considerably with the collector's orientation.