Diamond‐like carbon (DLC) coatings are commonly used to reduce boundary and mixed friction in tribological contacts. Recent works at the FZG efficiency gear test rig show that the application of the DLC coating ZrCg (a‐C:H:Zr) on gear flanks reduces the mean coefficient of friction in fluid film lubrication regime by up to 39% compared with uncoated gear flanks. A common explanation is the lower heat dissipation of DLC coatings resulting in higher EHL contact temperatures, hence in lower effective lubricant viscosity in the EHL contact. To gain a deeper understanding, discrete ZrxC1−x coatings were deposited on AISI 5115 using physical vapour deposition technology and thermophysical properties were directly measured. The tribological behavior of the coatings was investigated at the FZG twin‐disc test rig by using mineral gear oil. The results clearly prove the strong influence of the thermophysical properties of the DLC coatings on fluid friction in highly loaded EHL contacts.

Purpose This paper aims to address the influence of diamond-like carbon (DLC) coatings on the frictional power loss of spur gears. It shows potentials for friction and bulk temperature reduction in industrial use. From a scientific point of view, the thermal insulation effect on fluid friction is addressed, which lowers viscosity in the gear contact due to increasing contact temperature. Design/methodology/approach Thermal insulation effect is analyzed in detail by means of the heat balance and micro thermal network of thermal elastohydrodynamic lubrication contacts. Preliminary results at a twin-disk test rig are summarized to categorize friction and bulk temperature reduction by DLC coatings. Based on experiments at a gear efficiency test rig, the frictional power losses and bulk temperatures of DLC-coated gears are investigated, whereby load, speed, oil temperature and coatings are varied. Findings Experimental investigations at the gear efficiency test rig showed friction and bulk temperature reduction for all operating conditions of DLC-coated gears compared to uncoated gears. This effect was most pronounced for high load and high speed. A reduction of the mean gear coefficient of friction on average 25% and maximum 55% was found. A maximum reduction of bulk temperature of 15% was observed. Practical implications DLC-coated gears show a high potential for reducing friction and improving load-carrying capacity. However, the industrial implementation is restrained by the limited durability of coatings on gear flanks. Therefore, a further and overall consideration of key durability factors such as substrate material, pretreatment, coating parameters and gear geometry is necessary. Originality/value Thermal insulation effect of DLC coatings was shown by theoretical analyses and experimental investigations at model test rigs. Although trial tests on gears were conducted in literature, this study proves the friction reduction by DLC-coated gears for the first time systematically in terms of various operating conditions and coatings. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2020-0257/

No abstract

Within this study, self-lubricating and triboactive (Cr,Al)N+Mo:S coatings were developed and investigated for the deposition on components in a low-temperature physical vapor deposition (PVD) hybrid process. Therefore, direct current magnetron sputtering (dcMS) and high power pulse magnetron sputtering (HPPMS) PVD were combined by using an industrial coating machine. Hereby, it was possible to deposit dense and smooth triboactive, self-lubricating nitride coatings with different chemical compositions and architectures on 16MnCr5E samples. Two coating architectures, a matrix monolayer and a graded coating structure, were developed to evaluate the effect on the tribological behavior. The morphology and coating thickness were analyzed by means of scanning electron microscopy (SEM). Furthermore, the indentation hardness and modulus of indentation as well as the compound adhesion between substrate materials and coating were analyzed. Tribological analyses of (Cr,Al)N+Mo:S-coated and uncoated samples were conducted under fluid-free friction regime at room temperature T = (20 ± 3) °C, a velocity v = 0.1 m/s and a distance s = 1000 m by varying the Hertzian contact pressure from 400 MPa ≤ pH ≤ 1300 MPa against steel counterparts, 100Cr6, in a pin-on-disk (PoD) tribometer. The graded coating architecture of (Cr,Al)N+Mo:S enabled a significant wear and friction reduction. Furthermore, Raman analyses prove the formation of solid lubrication tribofilm containing MoS2, MoO3 MoO2 and MoxOy at the toplayer of a graded (Cr,Al)N+Mo:S coating, which are responsible for the improved tribological behavior.

Purpose This paper aims to address the coating and compound analysis of diamond-like carbon (DLC) on steel, to understand the frictional behavior in tribological gear systems presented in paper Part I. Here, the Ti and Zr modified DLC coating architectures are analyzed regarding their chemical, mechanical and thermophysical properties. The results represent a systematic analysis of the thermal insulating effect in tribological contact of DLC coated gears. Design/methodology/approach The approach was to evaluate the effect of the substitution of Zr through Ti at the reference coating ZrCg to TiCg and the effect on thermophysical properties. Furthermore, the influence of different carbon and hydrogen contents on the coating and compound properties was analyzed. Therefore, different discrete Ti or Zr containing DLC coatings were deposited on an industrial coating machine. Thereby the understanding of the microstructure and chemical composition of the reference coatings is increased. Findings Results prove comparable mechanical properties of metal modified DLC independent of differences in chemical compositions. Moreover, the compound adhesion between TiCg/16MnCr5E was improved compared to ZrCg/16MnCr5E. The effect of hydrogen content Ψ and carbon content xc on the thermophysical properties is limited by Ψ = 18 at.% and xc = 90 at.%. Practical implications The findings of the combined papers Part I and II show a high potential for industrial application of DLC on gears. Based on the results DLC coatings and gears can be tailored to each other. Originality/value Systematic analysis of DLC coatings were conducted to evaluate the effect of titanium, carbon and hydrogen on thermophysical properties.