Nanomaterials are being extensively produced and applied in society. Human and environmental exposures are, therefore, inevitable and so increased attention is being given to nanotoxicity. While silica nanoparticles (NP) are one of the top five nanomaterials found in consumer and biomedical products, their toxicity profile is poorly characterized. In this study, we investigated the toxicity of silica nanoparticles with diameters 20, 50 and 80 nm using an in vivo zebrafish platform that analyzes multiple endpoints related to developmental, cardio-, hepato-, and neurotoxicity. Results show that except for an acceleration in hatching time and alterations in the behavior of zebrafish embryos/larvae, silica NPs did not elicit any developmental defects, nor any cardio- and hepatotoxicity. The behavioral alterations were consistent for both embryonic photomotor and larval locomotor response and were dependent on the concentration and the size of silica NPs. As embryos and larvae exhibited a normal touch response and early hatching did not affect larval locomotor response, the behavior changes observed are most likely the consequence of modified neuroactivity. Overall, our results suggest that silica NPs do not cause any developmental, cardio- or hepatotoxicity, but they pose a potential risk for the neurobehavioral system.

Gold nanoparticles functionalized with polyethylene glycol of different chain lengths are used to determine the influence of the capping layer thickness on the radiosensitizing effect of the particles. The size variations in organic coating, built up with polyethylene glycol polymers of molecular weight 1-20 kDa, allow an evaluation of the decrease in dose enhancement percentages caused by the gold nanoparticles at different radial distances from their surface. With localized eradication of malignant cells as a primary focus, radiosensitization is most effective after internalization in the nucleus. For this reason, we performed controlled radiation experiments, with doses up to 20 Gy and particle diameters in a range of 5-30 nm, and studied the relaxation pattern of supercoiled DNA. Subsequent gel electrophoresis of the suspensions was performed to evaluate the molecular damage and consecutively quantify the gold nanoparticle sensitization. In conclusion, on average up to 58.4% of the radiosensitizing efficiency was lost when the radial dimensions of the functionalizing layer were increased from 4.1 to 15.3 nm. These results serve as an experimental supplement for biophysical simulations and demonstrate the influence of an important parameter in the development of nanomaterials for targeted therapies in cancer radiotherapy.

Mesoporous silica nanoparticles (MSNPs) are gaining a large interest in the field of medical and biomedical applications due to their biodegradability and high loading capacity as a carrier. In this work, a simple synthesis and functionalization procedure is reported, which allows tuning the nanoparticle properties, functionalization, and biodegradability. Variations in the synthesis procedure are introduced, including temperature, concentration of catalyst, and surface functionalization. These samples are characterized and afterwards degraded in phosphate buffered saline (PBS) to determine their degradation kinetics. The amount of degraded material is colorimetrically determined, using an optimized protocol based on molybdenum blue chemistry. It is shown that the degradability of the nanoparticles increased with decreasing synthesis temperatures, lower amounts of catalyst, and higher concentrations of nanoparticles. Surface functionalization alters the degradation kinetics as well, rendering amino-functionalized nanoparticles the fastest degradation behavior, followed by carboxylated and nonfunctionalized nanoparticles. From these results, it can be concluded that the degradation rate of MSNPs can be varied from a few hours to several days by small changes in the synthesis procedure. Moreover, the degradation behavior is strongly dependent on the nanoparticle growth rate.

Nanoparticles of different materials are already in use for many applications. In some applications, these nanoparticles need to be deposited on a substrate in a fast and reproducible way. We have developed a new direct liquid injection system for nanoparticle deposition by chemical vapor deposition using a liquid nanoparticle precursor. The system was designed to deposit nanoparticles in a controlled and reproducible way by using two direct liquid injectors to deliver nanoparticles to the system. The nanoparticle solution is first evaporated and then the nanoparticles flow onto a substrate inside the vacuum chamber. To allow injection and evaporation of the liquid, a direct liquid injection and vaporization system are mounted on top of the process chamber. The deposition of the nanoparticles is controlled by parameters such as deposition temperature, partial pressure of the gases, and flow rate of the nanoparticle suspension. The concentration of the deposited nanoparticles can be varied simply by changing the flow rate and deposition time. We demonstrate the capabilities of this system using gold nanoparticles. The selected suspension flow rates were varied between 0.25 and 1 g/min. AFM analysis of the deposited samples showed that the aggregation of gold nanoparticles is well controlled by the flow and deposition parameters.

An optical flux sensor, based on the fluorescence properties of materials and nanoparticles, has been developed to control the deposition rate in thin film deposition systems. Using a simple diode laser and a photomultiplier tube with a light filter, we report the detection of gallium atoms and CdSe-ZnS quantum dots. This setup has a high sensitivity and reproducibility.