Radio frequency energy harvesting (RFEH) and wireless power transmission (WPT) are two emerging alternative energy technologies that have the potential to offer wireless energy delivery in the future. One of the key components of RFEH or WPT system is the receiving antenna. The receiving antenna's performance has a considerable impact on the power delivery capability of an RFEH or WPT system. This paper provides a well-rounded review of recent advancements of receiving antennas for RFEH and WPT. Antennas discussed in this paper are categorized as low-profile antennas, multi-band antennas, circularly polarized antennas, and array antennas. A number of contemporary antennas from each category are presented, compared, and discussed with particular emphasis on design approach and performance. Current design and fabrication challenges, future development, open research issues of the antennas and visions for RFEH and WPT are also discussed in this review.

This paper demonstrates the performance of a potential design of a paper substrate-based flexible antenna for intrabody telemedicine systems in the 2.4 GHz industrial, scientific, and medical radio (ISM) bands. The antenna was fabricated using 0.54 mm thick flexible photo paper and 0.03 mm copper strips as radiating elements. Design and performance analyses of the antenna were performed using Computer Simulation Technology (CST) Microwave Studio software. The antenna performances were investigated based on the reflection coefficient in normal and bent conditions. The total dimensions of the proposed antenna are 40 × 35 × 0.6 mm3. The antenna operates at 2.33–2.53 GHz in the normal condition. More than an 8% fractional bandwidth is expressed by the antenna. Computational analysis was performed at different flexible curvatures by bending the antenna. The minimum fractional bandwidth deviation is 5.04% and the maximum is 24.97%. Moreover, it was mounted on a homogeneous phantom muscle and a four-layer human tissue phantom. Up to a 70% radiation efficiency with a 2 dB gain was achieved by the antenna. Finally, the performance of the antenna with a homogeneous phantom muscle was measured and found reliable for wearable telemedicine applications.

A compact UHF antenna has been presented in this paper for nanosatellite space mission. A square ground plane with slotted rectangular radiating element have been used. Coaxial probe feeding is used to excite. The rectangular slot of the radiating patch is responsible for resonating at lower UHF bands. One of the square faces of the nanosatellite structure works as the ground plane for the slotted radiating element. The fabricated prototype of the proposed antenna has achieved an impedance bandwidth (S11< -10dB) of 7.0 MHz (398 MHz– 405 MHz) with small size of 97 mm× 90 mm radiating element. The overall ground plane size is 100 mm × 100 mm × 0.5 mm. The proposed antenna has achieved a gain of 1.18 dB with total efficiency of 62.5%. The proposed antenna addresses two design challenges of nanosatellite antenna, (a) assurance of the placement of solar panel beneath the radiating element; (b) providing about 50% open space for solar irradiance to pass onto the solar panel, enabling the solar panel to achieve up to 93.95% of power under of normal conditions.

No abstract

One of the most efficient methods to observe the impact of geographical, environmental, and geological changes is remote sensing. Nowadays, nanosatellites are being used to observe climate change using remote sensing technology. Communication between a remote sensing nanosatellite and Earth significantly depends upon antenna systems. Body-mounted solar panels are the main source of satellite operating power unless deployable solar panels are used. Lower ultra-high frequency (UHF) nanosatellite antenna design is a crucial challenge due to the physical size constraint and the need for solar panel integration. Moreover, nanosatellite space missions are vulnerable because of antenna and solar panel deployment complexity. This paper proposes a solar panel-integrated modified planner inverted F antenna (PIFA) to mitigate these crucial limitations. The antenna consists of a slotted rectangular radiating patch with coaxial probe feeding and a rectangular ground plane. The proposed antenna has achieved a −10 dB impedance bandwidth of 6.0 MHz (447.5 MHz–453.5 MHz) with a small-sized (80 mm× 90 mm× 0.5 mm) radiating element. In addition, the antenna achieved a maximum realized gain of 0.6 dB and a total efficiency of 67.45% with the nanosatellite structure and a solar panel. The challenges addressed by the proposed antenna are to ensure solar panel placement between the radiating element and the ground plane, and provide approximately 55% open space to allow solar irradiance into the solar panel.